TFA1020 2-Layer 5mil Pure Gold High Frequency PCB for Aerospace & Radar Applications
(Note: Printed Circuit Boards are custom-made products. Images and parameters are for reference only.)
Brief introduction
The dielectric layer of the Polytetrafluoroethylene ceramic composite dielectric substrate TFA series consists of PTFE resin and ceramics, and is not produced using the traditional method of impregnating glass fiber cloth with resin to make prefabricated sheets. Instead, a new process is employed to create prefabricated sheets, which are then pressed using a special lamination process. This material exhibits outstanding electrical, thermal, and mechanical properties with excellent dielectric constant at the same level, making it an aerospace-grade high-frequency and high-reliability material that can replace similar foreign products.
This series of substrates does not contain glass fiber cloth. It utilizes a large amount of uniform special nano-ceramics mixed with resin, eliminating the fiberglass effect during the propagation of electromagnetic waves. It offers excellent frequency stability, with minimal dielectric loss at the same level. The material's X/Y/Z anisotropy is minimized, and it also features a low thermal expansion coefficient equivalent to copper foil and stable dielectric temperature characteristics.
The dielectric constant of this series includes four options: 2.94, 3.0, 6.15, and 10.2 for selection. The corresponding part numbers are TFA294, TFA300, TFA615, TFA1020.
This 2-layer rigid PCB is constructed entirely with TFA1020 as the core material at 5mil (0.127mm) thickness, with pure gold surface finish and 1oz copper on both sides. Its DK of 10.20 offers excellent high-frequency performance, making it ideal for demanding applications such as aerospace equipment, microwave antennas, phased array radars, satellite communications, and power amplifiers.
The dielectric constant of this series includes four options: 2.94, 3.0, 6.15, and 10.2 for selection. The corresponding part numbers are TFA294, TFA300, TFA615, TFA1020.
TFA series comes standard with RTF low-profile copper foil, which reduces conductor loss while providing excellent peel strength. Rolled copper foil is also available. TFA series can be paired with copper or aluminum bases.
TFA294 and TFA300 can be paired with embedded 50Ω resistor copper foil to form resistor film boards.
PCB processing can follow standard PTFE board process technology. The material's excellent mechanical and physical properties make it suitable for multilayer, high-multilayer, and backplane processing. It also demonstrates excellent processability in dense hole and fine line applications.
Technical features & benefits
- Dielectric Constant (DK): 10.20 ± 0.20 at 10GHz
- Dissipation Factor (Df): 0.0015 at 10GHz / 0.0017 at 20GHz
- Low TCDK: -340 ppm/°C (-55°C to 150°C)
- CTE matched to copper: X-axis 16 ppm/°C, Y-axis 16 ppm/°C, Z-axis 30 ppm/°C (-55°C to 288°C)
- High Thermal Conductivity: 0.88 W/mK
- Ultra-Low Moisture Absorption: 0.015%
- UL 94 V-0 Rated
- No glass fiber reinforcement — eliminates fiberglass effect during electromagnetic wave propagation
- Excellent frequency stability up to 77GHz (meets millimeter-wave and automotive radar requirements)
- Excellent radiation resistance — stable dielectric and physical properties after irradiation
- Low outgassing — meets aerospace vacuum outgassing requirements
- Low dielectric constant tolerance and excellent batch-to-batch consistency
- Standard RTF low-profile copper foil for reduced conductor loss and excellent peel strength
- Stable DK (10.20±0.20) — Consistent impedance control for high-frequency designs
- Ultra-Low Df (0.0015 @ 10GHz) — Excellent high-frequency performance with minimal signal loss
- No Glass Fiber Reinforcement — Uniform dielectric properties, no fiberglass effect
- CTE Matched to Copper (16/16/30 ppm/°C) — High reliability plated through holes and dimensional stability
- High Thermal Conductivity (0.88 W/mK) — Superior heat dissipation for high-power applications
- Excellent Radiation Resistance & Low Outgassing — Space-grade material for aerospace and defense applications
- Frequency Stability up to 77GHz — Meets millimeter-wave and automotive radar requirements
- Pure Gold Finish — Excellent solderability, corrosion resistance, and wire bondability
- Low DK tolerance and excellent batch-to-batch consistency:Consistent electrical performance across production batches
- Lowest dielectric loss at the same level:Superior signal integrity for high-frequency designs
- Excellent frequency and phase stability from -55°C to 150°C:Reliable performance across temperature extremes
- Ultra-low moisture absorption (0.015%):Stable performance in humid environments
- Pure Gold finish:Excellent solderability, corrosion resistance, wire bondability
Product images
PCB specifications
| Base material | Wangling TFA1020 (PTFE + Ceramic Composite) |
| Layer count | 2-layer rigid PCB |
| Board dimensions | 67.4mm x 89mm = 1 PCS, ±0.15mm |
| Minimum Trace/Space | 4/6 mils |
| Minimum Hole Size | 0.35mm |
| Blind vias | No |
| Finished board thickness | 0.25mm |
| Finished Cu weight | 1 oz (35 μm / 1.4 mils) all layers |
| Via plating thickness | 20 μm |
| Surface finish | Pure Gold |
| Top Silkscreen | No |
| Bottom Silkscreen | No |
| Top Solder Mask | No |
| Bottom Solder Mask | No |
| 100% Electrical test | Used prior to shipment |
Note: TFA series minimum thickness is 0.127mm (5mil). Multiples of 0.127mm thickness are available. Please specify whether "total thickness including copper" or "dielectric thickness" is required when ordering.
| Standard Dielectric Thicknesses (mm/mil) | 0.127mm (5mil), 0.254mm (10mil), 0.508mm (20mil), 0.635mm (25mil), 0.762mm (30mil), 1.016mm (40mil), 1.270mm (50mil), 1.524mm (60mil), 1.905mm (75mil), 2.03mm (80mil), 2.54mm (100mil), 3.175mm (125mil), 3.81mm (150mil), 4.06mm (160mil), 5.08mm (200mil), 6.35mm (250mil) |
| Standard Panel Sizes | 305×460mm (12×18"), 460×610mm (18×24") |
| Standard Claddings | RTF Low-Profile Copper: 0.5oz (18μm), 1oz (35μm); Rolled Copper available; Embedded 50Ω resistor copper foil available |
| DK Options (TFA Series) | 2.94 (TFA294), 3.0 (TFA300), 6.15 (TFA615), 10.2 (TFA1020) |
| Metal Base Options | TFA***-AL (Aluminum base), TFA***-CU (Copper base) for shielding/heat dissipation |
Layer stack-up
- Layer: Copper_layer_1 (Top), Material: Copper, Thickness: 35 μm (1 oz)
- Layer: Dielectric, Material: TFA1020 Core, Thickness: 0.127 mm (5mil)
- Layer: Copper_layer_2 (Bottom), Material: Copper, Thickness: 35 μm (1 oz)
PCB Statistics
- Components: 24
- Total Pads: 30
- Thru Hole Pads: 18
- Top SMT Pads: 12
- Bottom SMT Pads: 0
- Vias: 11
- Nets: 2
Application areas
- Aerospace equipment, space systems, in-cabin equipment, aircraft
- Microwave applications, antennas, phase-sensitive antennas
- Early warning radars, airborne radars, and various radar systems
- Phased array antennas and beamforming networks
- Satellite communications and navigation systems
- Power amplifiers and combiners
- Millimeter-wave and automotive radar applications (up to 77GHz)
- Aerospace equipment, space systems, in-cabin equipment, aircraft
- Microwave applications, antennas, phase-sensitive antennas
- Early warning radars, airborne radars, and various radar systems
- Phased array antennas and beamforming networks
- Satellite communications and navigation systems
- Power amplifiers and combiners
- Millimeter-wave and automotive radar applications (up to 77GHz)
Properties
TFA1020 Typical Properties
| Property | TFA1020 | Dir. | Units | Condition | Test Method |
|---|---|---|---|---|---|
| Dielectric Constant (Typical), 10 GHz | 10.20 | Z | — | 10 GHz | IPC-TM-650 2.5.5.5 |
| Dielectric Constant (Design), 10 GHz | 10.7 | Z | — | 10 GHz | 50Ω microstrip line |
| Dk Tolerance | ±0.20 | — | — | — | — |
| Dissipation Factor, 10 GHz | 0.0015 | Z | — | 10 GHz | IPC-TM-650 2.5.5.5 |
| Dissipation Factor, 20 GHz | 0.0017 | — | — | 20 GHz | — |
| Dissipation Factor, 40 GHz | — | — | — | 40 GHz | — |
| Thermal Coefficient of Dk | -340 | — | ppm/°C | -55 to 150°C | IPC-TM-650 2.5.5.5 |
| Copper Peel Strength (1 oz RTF) | >1.6 | — | N/mm | 1 oz RTF copper | IPC-TM-650 2.4.8 |
| Volume Resistivity | ≥5×10⁷ | — | MΩ·cm | C96/23/95 | IPC-TM-650 2.5.17.1 |
| Surface Resistance | ≥5×10⁷ | — | MΩ | C96/23/95 | IPC-TM-650 2.5.17.1 |
| Electrical Strength (Z-direction) | >30 | — | KV/mm | 5 kW, 500 V/s | IPC-TM-650 2.5.6 |
| Breakdown Voltage (X/Y) | >25 | — | KV | 5 kW, 500 V/s | IPC-TM-650 2.5.6 |
| CTE (X, Y) | 16, 16 | X,Y | ppm/°C | -55 to 288°C | IPC-TM-650 2.4.41 |
| CTE (Z) | 30 | Z | ppm/°C | -55 to 288°C | IPC-TM-650 2.4.41 |
| Water Absorption | 0.015 | — | % | 20±2°C, 24 h | IPC-TM-650 2.6.2.1 |
| Density | 3.0 | — | g/cm³ | Room temp | ASTM D792 |
| Thermal Conductivity (Z) | 0.88 | Z | W/(m·K) | — | ASTM D5470 |
| Td (onset) | 505 | — | °C | TGA | IPC-TM-650 2.4.24.6 |
| Flammability | V-0 | — | — | — | UL 94 |
Quality Assurance
- Type of artwork supplied: Gerber RS-274-X
- Accepted standard: IPC-Class-2
- Availability: Worldwide
- 100% Electrical test prior to shipment
- Type of artwork supplied: Gerber RS-274-X
- Accepted standard: IPC-Class-2
- Availability: Worldwide
- 100% Electrical test prior to shipment
TFA1020 Electrical Performance Characteristics
- Excellent Frequency Stability: The material maintains a stable dielectric constant and low loss values across the 0.5~20GHz frequency range, meeting design requirements across different frequencies.
- Excellent Temperature Stability: TCDK is approximately -340 ppm/°C over the -55~150°C range, providing reference data for designs across different temperatures. The actual usable temperature of the material far exceeds this range.
Excellent Frequency Stability: The material maintains a stable dielectric constant and low loss values across the 0.5~20GHz frequency range, meeting design requirements across different frequencies.
Excellent Temperature Stability: TCDK is approximately -340 ppm/°C over the -55~150°C range, providing reference data for designs across different temperatures. The actual usable temperature of the material far exceeds this range.
TFA Series Aluminum/Copper Base Option
The TFA series can also be provided with an aluminum or copper base, where one side of the dielectric layer is covered with copper foil and the other side is laminated with copper or aluminum for shielding or heat dissipation purposes. Model designation: TFA***-AL or TFA***-CU.
| Model | Metal Base | Specific Gravity | Thermal Conductivity | CTE | Available Metal Thickness | Thickness Tolerance | Available Sizes |
|---|---|---|---|---|---|---|---|
| TFA***-CU | Copper (Purple/Brass) | 8.9 | 380 W/(M·K) | 17 ppm/°C | 0.48, 0.98, 1.48, 1.98, 2.98, 3.98mm (other thicknesses available upon request) | +0.02, -0.05 | 460×610mm, 460×305mm |
| TFA***-AL | Aluminum | 2.7 | 180 W/(M·K) | 24 ppm/°C | 0.48, 0.98, 1.48, 1.98, 2.98, 3.98mm (other thicknesses available upon request) | +0.02, -0.05 | 460×610mm, 460×305mm |
Example: TFA1020-AL represents TFA1020 with aluminum base. TFA1020-CU represents TFA1020 with copper base.
Data Source Notes
- Dielectric Constant (Typical) is tested in the Z-direction of the material using GB/T 12636-1990 or IPC-TM-650 2.5.5.5 Stripline method.
- Dielectric Constant (Design) is tested using the 50Ω Microstrip Line method, also in the Z-direction.
- Other properties are tested using or referencing IPC-TM-650 or GBT4722-2017 standard test methods.
- All test data are typical measurement values intended to assist customers in material selection. They do not constitute any express or implied warranty and do not guarantee performance in specific applications. Customers are responsible for verifying the suitability of Wangling materials for each application.
Dielectric Constant (Typical) is tested in the Z-direction of the material using GB/T 12636-1990 or IPC-TM-650 2.5.5.5 Stripline method.
Dielectric Constant (Design) is tested using the 50Ω Microstrip Line method, also in the Z-direction.
Other properties are tested using or referencing IPC-TM-650 or GBT4722-2017 standard test methods.
All test data are typical measurement values intended to assist customers in material selection. They do not constitute any express or implied warranty and do not guarantee performance in specific applications. Customers are responsible for verifying the suitability of Wangling materials for each application.
Tell us the board. We answer within 4 hours.
Large Gerber files are easier by email — this form gets the conversation started with the right engineer.
Send requestOr email your files torfq@bichengcircuits.com
