BICHENGPCBBicheng Technologies Limited

DFM

Design For Manufacture (1)1-JAN-2023
Serial NO.ProcedureItemLarge volume (S<100 m²)Middle volume (S<10 m²)Prototype(S<1m²)
1Inner layer (18um, 35um, 70um etc are finished copper. If not mentioned copper, finished 1oz is the default value )Min.dielectric layer0.1mm0.1mm0.05mm
2Min.track and spacing5/5mil(18um)4/4mil(18um)3/3.5mil(18um)
35/5mil(35um)4/4mil(35um)3/4mil(35um)
47/9mil(70um)6/8mil(70um)6/7mil(70um)
59/11mil(105um)8/10mil(105um)8/9mil(105um)
613/13mil(140um)12/12mil(140um)12/11mil(140um)
7Min.distance from drill to conductor4 Layer 10mil,6 layer 10mil,8-12 layer 12mil4 layer 8mil,6 layer 8mil,8-12 layer 10mil,14-20 layer 14mil,22-32 layer 18mil4 layer 6mil,6 layer 6mil,8-14 layer 8mil,16-22 layer 12mil,24-32 layer 14mil
8Min.width of annular ring on inner layer4 Layer 10mil(35um),≥6 Layer 14mil(35um)4 Layer 8mil(35um),≥6 layer 12mil(35um)4 Layer 6mil(35um),≥6 Layer 10mil(35um)
9Inner layer isolation ring width(Min)10mil (35um)8mil (35um)6mil (35um)
10Min.via pad diameter20mil (35um)16mil (35um)16mil (35um)
11Min. distance from board edge to conductor(no copper exposured)14 mil(35um)12 mil(35um)8 mil(35um)
12Maximum copper weight (Inner layer)12 OZ( 420 um )12 OZ ( 420 um )12 OZ ( 420 um )
13Different copper foil between layers17.5 / 210 um17.5 / 210 um17.5 / 210 um
14Inner layer BGA channelAbove 5 mil (18 um, 35 um coppper), above 6.5 mil (70um copper)
15AOICopper weight105um
16Test capability2mil /2mil

Design For Manufacture (2)

Serial NO.ProcedureItemManufacturing capability
Large volume (S<100 m²)Middle volume (S<10 m²)Prototype(S<1m²)
17LaminatingTolerance of laminating thickness±10% PCB thick±10% PCB thick±8% PCB thick
18Maximum laminating thickness10.0mm10.0mm10.0mm
19Laminating alignment accuracy≤±4 mil≤±3 mil≤±3 mil
20Drill (18um, 35um, 70um etc are finished copper. If not mentioned copper, finished 1oz is the default value )Min.diameter of drill bit0.1mm0.1mm0.1mm
21Min.diameter of slot router0.50mm0.50mm0.50mm
22Min.tolerance of PTH slots±0.102mm±0.102mm±0.102mm
23Max.aspect ratio1:161:161:16
24Hole tolerance±3mil±3mil±3mil
25Space of via to via6mil(same net),12mil(different net)6mil(same net),12mil(different net)6mil(same net),12mil(different net)
26Space of component hole to component hole10mil(same net),10mil(different net)10mil(same net),10mil(different net)10mil(same net),10mil(different net)
27Controlled drillTolerance of depth+/- 2mil
28Concentric Accuracy of Back drill hole+/- 2mil
29Dielectric thickness of Back drill≥4mil
30Diameter of back drill0.3mm ~ 6.5mm
31Back drill STUB2~6 mil
32Laser drillSurface copper9-12um
33Diameter4mil, 5mil
34MaterialEpoxy(106, 1080, 2113), Hydracarbon, PPO/PPE
35EtchingMin.width of etching logo8mil(12um,18um base copper),10 mil (35um base copper),12 mil(70um)
36Etch factor1.6-2.21.6-2.21.6-2.2
37Outer layer(18um, 35um, 70um etc are finished copper. If not mentioned copper, finished 1oz is the default value )Min.via pad diameter20mil16mil16mil
38Min.BGA pad diameter8mil8mil8mil
39Min.track and spacingbase copper 12um, finished 30um2.5mil / 2.5mil
base copper 17um, finished 35um2.8mil / 2.8mil
base copper 35um, finished 53um3.5mil / 3.5mil
base copper 53um, finihsed 70um5.0mil / 5.0mil
base copper 70um, finished 87.5um5.0mil / 6.0mil
40base copper 87.5um7.0mil / 7.0mil
41base copper 105um8.0mil / 8.0mil
42base copper 140um10.0mil / 10.0mil
43base copper 175um11mil / 11mil
44base copper 210um12mil / 12mil
456oz ~ ≤12oz: For each additional 1 oz, the capacity increases by 1.5/1.5 mil.
46Minimum grid10/10mil(35um)8/8mil(35um)4/8mil(35um)
47Min.space (conductor to pad, pad to pad)6mil(18um)5mil(18um)4mil(18um)
6mil(35um)5mil(35um)4mil(35um)
9mil(70um)8mil(70um)7mil(70um)
11mil(105um)10mil(105um)9mil(105um)
13mil(140um)12mil(140um)11mil(140um)
48Different copper foil between layers17.5 / 210 um

Design For Manufacture (3)

Serial NO.ProcedureItemManufacturing capability
Large volume (S<100 m²)Middle volume (S<10 m²)Prototype(S<1m²)
49Solder mask (18um, 35um, 70um etc are finished copper. If not mentioned copper, finished 1oz is the default value )Maximum via-plug diameter0.65mm0.65mm0.65mm
50Maximum PCB finished thickness of via-plug3.2mm3.2mm3.2mm
51Min.width of solder mask bridgebase copper ≦35umGreen4mil
52Others5mil
53copper 70-140umAll of colours6mil
54base copper >140umAll of colours8 mil
55Min. solder mask openingsingle side 1mil (full gold plated PCB, partial area 2mil is allowed; Other PCB, parital area 1.5mil is allowed.
56Min.solder mask covering traces.1.5mil (partial area 1.0mil is allowed
57Min. width of opening characters8mil
58Min.width of solder mask characters9mil(35um)9mil(35um)8mil(35um)
59Min.thickness of Solder mask9um(35um)9um(35um)9um(35um)
60Max.thickness of solder mask30um(35um)30um(35um)30um(35um)
61ColourGreen, Yellow, Orange, Black, Blue, Red, White, Matt green, Matt black, Matt blue, Purple, Gray
62Tolerance of Thickness±5um
63Min.height of opening character8mil
64Notation / Characters (Silkscreen)Min.width and height12um, 18um base copperWidth: 4milHeight: 25mil
6535um base copperWidth: 4milHeight: 30mil
66≥70um base copperWidth: 6milHeight: 45mil
67Min.gap from Characters to pads6mil6mil5mil
68ColourWhite, Black, Yellow
69Notation / Characters (Inkjet)Min.Width2mil2mil2mil
70Min.Heightbase copper ≦70um: 20mil
71base copper >70um: 30mil
72base copper >140um: 40mil
73ColourWhite

Design For Manufacture (4)

Serial NO.ProcedureItemManufacturing capability
Large volume (S<100 m²)Middle volume (S<10 m²)Prototype(S<1m²
74Carbon inkCarbon ink covers conductor or pads14mil13mil12mil
75Mid distance from carbon ink to pads12mil11mil10mil
76Peelable maskPeelable mask covers conductor or pads8mil7mil6mli
77Min.distance from peelable mask to pads14mil13mil12mil
78Max.via-plug of Silk-screen method2.0mm2.0mm2.0mm
79Max. via-plug of aluminum foil method4.5mm4.5mm4.5mm
80HASLPCB thickness of HASL0.6-4.0mm (Hole less 0.5mm should be use via-plug or mask-tent )
81HASL PCB Size22" x 24.5" (558.8mm x 622.3mm)
82Min.BGA size of HASL10mil
83Min. spacing for HASL dense board without solder mask6mil
84Thickness of Surface finishENIGNickle0.5~8um
85Gold0.025~0.127um
86Edge connector / Gold fingerNickle2.5~12.7um
87Gold0.125~2.0um
88HASL2.54-6.35um
89OSP0.2-0.4um
90Immersion tin (Horizontal)0.8-1.5um
91Immersion silver (Horizontal)0.1-0.3um
92ENEPIGNickle3~10um
93Palladium0.05~0.4um
94Gold0.025~0.127um

Design For Manufacture (5)

Serial NO.ProcedureItemManufacturing capability
Large volume (S<100 m²)Large volume (S<100 m²)Prototype(S<1m²)
95CNC Router ContourMethod of contour processCNC milling, V-CUT, Break-out tap, break-out holes, Punching
96Minimum router0.6mm
97Accuracy of contour±0.15mm±0.13mm±0.1mm
98Min.distance of milling contour(no copper exposure)10mil10mil8mil
99V-CUTAngle of V-CUT20°、30°、45°、60° ±5 °
100Minimum distance for V-CUT without exposing copper0.3mm (20° tool), 0.4mm (30° tool), 0.5mm (45° tool), 0.65mm (60°)
101Small Board V-Cut MachineMinimum board width:40mm
102Maximum board width:470mm
103Minimum board thickness:0.4mm
104Maximum board thickness:2.0mm
105Non-continuous V-CUT spacing:≥ 8 mm
106Big Board V-Cut MachineMinimum board thickness:0.4mm
107Maximum board thickness:3.5mm
108Non-continuous V-CUT spacing:≥ 15 mm
109Minimum V-CUT residual thickness.0.2mm
110V-CUT residual thickness tolerance±0.075 mm (only positive tolerance is allowed when residual thickness is 0.2)
111Alignment tolerance for upper and lower V-CUT lines±0.075 mm
112Min. distance from edge to V-Cut (no copper exposure)18mil (1.6mm Thick, 20 degree V-groove cutter)14mil(1.6mm Thick, 20 degree V-groove cutter)12mil (1.6mm Thick, 20 degree V-groove cutter)
11320mil (1.6mm Thick, 30 degree V-groove cutter)18mil (1.6mm Thick, 30 degree V-groove cutter)16mil (1.6mm Thick, 30 degree V-groove cutter)
11416mil (1.6mm Thick, 30 degree V-groove cutter)22mil (1.6mm Thick, 45 degree V-groove cutter)20mil (1.6mm Thick, 45 degree V-groove cutter)
11530mil (1.6mm Thick, 60 degree V-groove cutter)28mil (1.6mm Thick, 60 degree V-groove cutter)26mil (1.6mm Thick, 60 degree V-groove cutter)

Design For Manufacture (6)

Serial NO.ProcedureItemManufacturing capability
Large volume (S<100 m²)Large volume (S<100 m²)Prototype(S<1m²)
116Flying TestBoard thickness of flying probe test0.05-10.0mm
117Standard flying probe size22" x 26" (558.8mm x 660.4mm) (including four-wire low resistance)
118Maximum test size30" x 47.2" (762mm x 1198.88mm)
119Minimum distance from test points to board edge.0.5mm (Limited to one set of opposite edges.)
120Minimum continuity resistance10 Ω
121Maximum insulation resistance100 MΩ
122
123Maximum voltage500 V
124Minimum pads3 mil
125Minimum pad spacing3.9 mil
126Special tolerancePanel size of fixture test methodSize≤460X380mm, Small size can be compensated through manufacturing procedure
127Board thickness of fixture test method0.4-6.0mm
128Tolerance of press-fit hole±2mil
129Tolerance of NPTH±2mil
130Tolerance of PCB thickness1.0mm≥PCB thickness, Tolerance ±0.1mm;1.0mm≤PCB thickness, Tolerance ±10%
131Tolerance of depth of countersunk hole±0.2mm
132Depth tolerance of blind slot±0.2mm
133Maximum shipment sizeSize≤1200X600mm(Double side, no test required)
134Size≤1000X600mm( Multilayer, no test required)
135Minimum shipment size5mm x 5mm
136PCB thickness0.13-10.0mm
137Max. drill diameterSize≤6.5mm (Counterbore or router will be used for holes more than 6.5mm, Min.tolerance ±0.1mm )
138Max. countersink diameterSize≤6.5mm Countersink can be used counterbore drill or router)
139Distance of BevelSize≥11mmSize≥5mmSize≥5mm
140Thickness of peelable mask0.3-1.5mm ±0.15mm

Need a quote or engineering support?

Send us your Gerber, layer count and quantity — you get a DFM note and an indicative price within 4 working hours.

Get a quote

Or email us atrfq@bichengcircuits.com