F4BM255 2-Layer 3mm 2OZ Immersion Gold High Frequency PCB for RF & Microwave
(Note: Printed Circuit Boards are custom-made products. Images and parameters are for reference only.)
Brief introduction
Wangling's F4BM255 laminates are made by scientifically formulating and strictly pressing a combination of fiberglass cloth, polytetrafluoroethylene resin, and polytetrafluoroethylene film. Its electrical performance is improved compared to F4B255, mainly due to lower dielectric loss, increased insulation resistance, and improved stability. It can replace similar foreign products.
F4BM255 and F4BME255 have the same dielectric layer but different copper foil combinations: F4BM255 is paired with ED copper foil, suitable for applications without PIM requirements; F4BME255 is paired with reverse-treated foil (RTF) copper foil, offering excellent PIM performance, more precise line control, and lower conductor loss.
By adjusting the ratio between polytetrafluoroethylene and fiberglass cloth, F4BM255 and F4BME255 achieve precise control of the dielectric constant, providing low loss and enhanced dimensional stability. A higher dielectric constant corresponds to a higher proportion of fiberglass, resulting in better dimensional stability, lower thermal expansion coefficient, improved temperature drift, and a slight increase in dielectric loss.
This 2-layer rigid PCB is constructed entirely with F4BM255 as the core material at 3.0mm (3.1mm finished) thickness, with immersion gold surface finish and 2oz ED copper on both sides. Its DK of 2.55 offers excellent high-frequency performance, making it ideal for demanding applications such as microwave, RF, radar, phase shifters, power dividers, couplers, phased array antennas, satellite communications, and base station antennas.
F4BM255 features a dielectric constant of 2.55±0.05 at 10GHz, low dissipation factor of 0.0013 at 10GHz and 0.0018 at 20GHz, and excellent thermal stability. The material operates reliably across a wide temperature range from -55°C to +260°C and is suitable for mass production with high cost-performance.
Technical features & benefits
- Dielectric Constant (DK): 2.55 ± 0.05 at 10GHz
- DK Range: 2.17 ~ 3.0 optional, DK customizable
- Dissipation Factor (Df): 0.0013 at 10GHz / 0.0018 at 20GHz
- Low loss performance
- TCDK: -110 ppm/°C (-55°C to 150°C)
- Peel Strength (1oz F4BM): >1.8 N/mm
- Volume Resistivity: ≥6×10⁶ MΩ·cm
- Surface Resistivity: ≥1×10⁶ MΩ
- Electrical Strength (Z direction): >25 KV/mm
- Breakdown Voltage (XY direction): >34 KV
- CTE (XY direction): 16/21 ppm/°C (-55°C to 288°C)
- CTE (Z direction): 173 ppm/°C (-55°C to 288°C)
- Thermal Conductivity: 0.33 W/(M·K)
- Density: 2.25 g/cm³
- Moisture Absorption: ≤0.08%
- Long-term Operating Temperature: -55°C to +260°C
- UL 94 V-0 Flammability Rating
- Irradiation resistance and low outgassing
- Commercialization, mass production, high cost-performance
- Stable DK (2.55±0.05) — Consistent impedance control for high-frequency designs
- Low Df (0.0013 @ 10GHz) — Excellent signal integrity with minimal insertion loss
- 2OZ ED Copper Foil — High current handling capability for power applications
- Wider DK Range (2.17 ~ 3.0) — Flexible design options, DK customizable
- Low CTE (16/21 ppm/°C XY direction) — Excellent dimensional stability
- Irradiation Resistance & Low Outgassing — Suitable for aerospace and defense applications
- Commercialization & High Cost-Performance — Mass production ready
- Immersion Gold Finish — Excellent solderability, corrosion resistance, and wire bondability
- DK 2.55 ± 0.05 @ 10GHz:Stable dielectric constant for consistent impedance control
- Df 0.0013 @ 10GHz / 0.0018 @ 20GHz:Low loss for high-frequency RF and microwave designs
- 2OZ ED copper foil:High current capability for power RF applications
- DK 2.17 ~ 3.0 optional, customizable:Flexible design options
- UL 94 V-0 Rating:Flame retardant safety standard
- Irradiation resistance & low outgassing:Ideal for aerospace and defense applications
- Immersion Gold finish:Excellent solderability, corrosion resistance, wire bondability
Product images
PCB specifications
| Base material | Wangling F4BM255 (PTFE + Fiberglass + ED Copper Foil) |
| Layer count | 2-layer rigid PCB |
| Board dimensions | 521mm x 59mm = 1 PCS, ±0.15mm |
| Minimum Trace/Space | 7/7 mils |
| Minimum Hole Size | 0.4mm |
| Blind vias | No |
| Finished board thickness | 3.1mm |
| Finished Cu weight | 2oz (70 μm / 2.8 mils) all layers |
| Via plating thickness | 20 μm |
| Surface finish | Immersion Gold |
| Top Silkscreen | White |
| Bottom Silkscreen | No |
| Top Solder Mask | Green |
| Bottom Solder Mask | No |
| 100% Electrical test | Used prior to shipment |
Note: The following thicknesses can be produced as either total thickness including copper or dielectric thickness. Please specify when ordering.
| Standard Dielectric Thicknesses (mm) | 0.1, 0.127, 0.2, 0.25, 0.5, 0.508, 0.762, 0.8, 1.0, 1.5, 1.524, 1.575, 2.0, 2.5, 3.0, 4.0, 5.0, 6.0, 8.0, 10.0, 12.0 |
| Thickness Tolerances (mm) | 0.1mm: ±0.01, 0.127mm: ±0.01, 0.2mm: ±0.02, 0.25mm: ±0.02, 0.5mm: ±0.04, 0.508mm: ±0.04, 0.762mm: ±0.05, 0.8mm: ±0.05, 1.0mm: ±0.05, 1.5mm: ±0.06, 1.524mm: ±0.06, 1.575mm: ±0.06, 2.0mm: ±0.08, 2.5mm: ±0.08, 3.0mm: ±0.09, 4.0mm: ±0.1, 5.0mm: ±0.1, 6.0mm: ±0.12, 8.0mm: ±0.15, 10.0mm: ±0.18, 12.0mm: ±0.2 |
| Standard Panel Sizes | 460×610mm, 500×600mm, 850×1200mm, 914×1220mm, 1000×1200mm |
| Custom Panel Sizes | 300×250mm, 350×380mm, 500×500mm, 840×840mm, 1000×1500mm |
| F4BM Claddings (ED Copper) | 0.5oz (0.018mm), 1oz (0.035mm), 1.5oz (0.05mm), 2oz (0.07mm) |
| F4BME Claddings (RTF Copper) | 0.5oz (0.018mm), 1oz (0.035mm) |
| DK Options (F4B Series) | 2.17 ~ 3.0 (customizable) |
| Metal Base Options | F4BM***-AL (Aluminum base), F4BM***-CU (Copper base) for shielding/heat dissipation |
Note: For thicknesses ≥4.0mm or ≤0.2mm, panel size cannot exceed 500×610mm.
Layer stack-up
- Layer: Copper_layer_1 (Top), Material: Copper (ED), Thickness: 70 μm (2oz)
- Layer: Dielectric, Material: F4BM255 Core, Thickness: 3.0 mm
- Layer: Copper_layer_2 (Bottom), Material: Copper (ED), Thickness: 70 μm (2oz)
PCB Statistics
- Components: 28
- Total Pads: 194
- Thru Hole Pads: 148
- Top SMT Pads: 46
- Bottom SMT Pads: 0
- Vias: 43
- Nets: 2
Application areas
- Microwave, RF, and radar systems
- Phase shifters and passive components
- Power dividers, couplers, and combiners
- Feed networks and phased array antennas
- Linear antenna substrates
- Satellite communications and base station antennas
- High-frequency RF and microwave circuits
- Microwave, RF, and radar systems
- Phase shifters and passive components
- Power dividers, couplers, and combiners
- Feed networks and phased array antennas
- Linear antenna substrates
- Satellite communications and base station antennas
- High-frequency RF and microwave circuits
Properties
F4BM255 Typical Properties
| Property | F4BM255 | Dir. | Units | Condition | Test Method |
|---|---|---|---|---|---|
| Dielectric Constant (Typical), 10 GHz | 2.55 | — | — | 10 GHz | — |
| Dk Tolerance | ±0.05 | — | — | — | — |
| Dissipation Factor, 10 GHz | 0.0013 | — | — | 10 GHz | — |
| Dissipation Factor, 20 GHz | 0.0018 | — | — | 20 GHz | — |
| Thermal Coefficient of Dk | -110 | — | ppm/°C | -55 to 150°C | — |
| Peel Strength (F4BM, 1oz ED) | >1.8 | — | N/mm | 1 oz ED copper | — |
| Peel Strength (F4BME, 1oz RTF) | >1.6 | — | N/mm | 1 oz RTF copper | — |
| Volume Resistivity | ≥6×10⁶ | — | MΩ·cm | Room temp | — |
| Surface Resistivity | ≥1×10⁶ | — | MΩ | Room temp | — |
| Dielectric Strength (Z) | >25 | — | kV/mm | 5 kV, 500V/s | — |
| Dielectric Breakdown (X/Y) | >34 | — | kV | 5 kV, 500V/s | — |
| CTE (X, Y) | 16, 21 | X,Y | ppm/°C | -55 to 288°C | — |
| CTE (Z) | 173 | Z | ppm/°C | -55 to 288°C | — |
| Moisture Absorption | ≤0.08 | — | % | 20±2°C, 24 hrs | — |
| Density | 2.25 | — | g/cm³ | Room temp | — |
| Thermal Conductivity (Z) | 0.33 | Z | W/(m·K) | — | — |
| Continuous Operating Temp | -55 to +260 | — | °C | — | — |
| Flammability | V-0 | — | — | — | UL94 |
Quality Assurance
- Type of artwork supplied: Gerber RS-274-X
- Accepted standard: IPC-Class-2
- Availability: Worldwide
- 100% Electrical test prior to shipment
- Type of artwork supplied: Gerber RS-274-X
- Accepted standard: IPC-Class-2
- Availability: Worldwide
- 100% Electrical test prior to shipment
F4B Series Aluminum/Copper Base Option
The F4BM and F4BME series can also be provided with an aluminum or copper base, where one side of the dielectric layer is covered with copper foil and the other side is laminated with copper or aluminum for shielding or heat dissipation purposes. Model designation: F4BM***-AL, F4BME***-AL, F4BM***-CU, F4BME***-CU.
| Model | Metal Base | Specific Gravity | Thermal Conductivity | CTE | Available Metal Thickness | Thickness Tolerance | Available Sizes |
|---|---|---|---|---|---|---|---|
| F4BM***-CU / F4BME***-CU | Copper (Purple/Brass) | 8.9 | 380 W/(M·K) | 17 ppm/°C | 0.48, 0.98, 1.48, 1.98, 2.98, 3.98mm (other thicknesses available upon request) | +0.02, -0.05 | 460×610mm, 460×305mm (other sizes available upon request) |
| F4BM***-AL / F4BME***-AL | Aluminum | 2.7 | 180 W/(M·K) | 24 ppm/°C | 0.48, 0.98, 1.48, 1.98, 2.98, 3.98mm (other thicknesses available upon request) | +0.02, -0.05 | 460×610mm, 460×305mm (other sizes available upon request) |
Example: F4BM255-AL represents F4BM255 with aluminum base. F4BM255-CU represents F4BM255 with copper base.
Data Source Notes
- Dielectric Constant is tested in the Z-direction of the material using GB/T 12636-1990 or IPC-TM-650 2.5.5.5 Stripline method.
- Other properties are tested using or referencing IPC-TM-650 or GBT4722-2017 standard test methods.
- All test data are typical measurement values intended to assist customers in material selection. They do not constitute any express or implied warranty and do not guarantee performance in specific applications. Customers are responsible for verifying the suitability of Wangling materials for each application.
Dielectric Constant is tested in the Z-direction of the material using GB/T 12636-1990 or IPC-TM-650 2.5.5.5 Stripline method.
Other properties are tested using or referencing IPC-TM-650 or GBT4722-2017 standard test methods.
All test data are typical measurement values intended to assist customers in material selection. They do not constitute any express or implied warranty and do not guarantee performance in specific applications. Customers are responsible for verifying the suitability of Wangling materials for each application.
Tell us the board. We answer within 4 hours.
Large Gerber files are easier by email — this form gets the conversation started with the right engineer.
Send requestOr email your files torfq@bichengcircuits.com
