F4BM245 2-Layer 20mil Immersion Gold High Frequency PCB for RF & Radar Applications
(Note: Printed Circuit Boards are custom-made products. Images and parameters are for reference only.)
Brief introduction
Wangling's F4BM245 laminates are made by scientifically formulating and strictly pressing a combination of fiberglass cloth, polytetrafluoroethylene resin, and polytetrafluoroethylene film. Its electrical performance is improved compared to F4B245, mainly due to lower dielectric loss, increased insulation resistance, and improved stability. It can replace similar foreign products.
F4BM245 and F4BME245 have the same dielectric layer but different copper foil combinations: F4BM245 is paired with ED copper foil, suitable for applications without PIM requirements; F4BME245 is paired with reverse-treated foil (RTF) copper foil, offering excellent PIM performance, more precise line control, and lower conductor loss.
By adjusting the ratio between polytetrafluoroethylene and fiberglass cloth, F4BM245 and F4BME245 achieve precise control of the dielectric constant, providing low loss and enhanced dimensional stability. A higher dielectric constant corresponds to a higher proportion of fiberglass, resulting in better dimensional stability, lower thermal expansion coefficient, improved temperature drift, and a slight increase in dielectric loss.
This 2-layer rigid PCB is constructed entirely with F4BM245 as the core material at 20mil (0.508mm) thickness, with immersion gold surface finish and 1oz ED copper on both sides. Its DK of 2.45 offers excellent high-frequency performance, making it ideal for demanding applications such as microwave, RF, radar, phase shifters, power dividers, couplers, phased array antennas, satellite communications, and base station antennas.
F4BM245 features a dielectric constant of 2.45±0.05 at 10GHz, low dissipation factor of 0.0012 at 10GHz and 0.0017 at 20GHz, and excellent thermal stability. The material operates reliably across a wide temperature range from -55°C to +260°C and is suitable for mass production with high cost-performance.
Technical features & benefits
- Dielectric Constant (DK): 2.45 ± 0.05 at 10GHz
- DK Range: 2.17 ~ 3.0 optional, DK customizable
- Dissipation Factor (Df): 0.0012 at 10GHz / 0.0017 at 20GHz
- Low loss performance
- TCDK: -120 ppm/°C (-55°C to 150°C)
- Peel Strength (1oz F4BM): >1.8 N/mm
- Volume Resistivity: ≥6×10⁶ MΩ·cm
- Surface Resistivity: ≥1×10⁶ MΩ
- Electrical Strength (Z direction): >25 KV/mm
- Breakdown Voltage (XY direction): >32 KV
- CTE (XY direction): 20/25 ppm/°C (-55°C to 288°C)
- CTE (Z direction): 187 ppm/°C (-55°C to 288°C)
- Thermal Conductivity: 0.30 W/(M·K)
- Density: 2.22 g/cm³
- Moisture Absorption: ≤0.08%
- Long-term Operating Temperature: -55°C to +260°C
- UL 94 V-0 Flammability Rating
- Irradiation resistance and low outgassing
- Commercialization, mass production, high cost-performance
- Stable DK (2.45±0.05) — Consistent impedance control for high-frequency designs
- Low Df (0.0012 @ 10GHz) — Excellent signal integrity with minimal insertion loss
- ED Copper Foil — Cost-effective solution for applications without PIM requirements
- Wider DK Range (2.17 ~ 3.0) — Flexible design options, DK customizable
- Low CTE (20/25 ppm/°C XY direction) — Excellent dimensional stability
- Irradiation Resistance & Low Outgassing — Suitable for aerospace and defense applications
- Commercialization & High Cost-Performance — Mass production ready
- Immersion Gold Finish — Excellent solderability, corrosion resistance, and wire bondability
- DK 2.45 ± 0.05 @ 10GHz:Stable dielectric constant for consistent impedance control
- Df 0.0012 @ 10GHz / 0.0017 @ 20GHz:Low loss for high-frequency RF and microwave designs
- DK 2.17 ~ 3.0 optional, customizable:Flexible design options
- UL 94 V-0 Rating:Flame retardant safety standard
- Irradiation resistance & low outgassing:Ideal for aerospace and defense applications
- Immersion Gold finish:Excellent solderability, corrosion resistance, wire bondability
Product images
PCB specifications
| Base material | Wangling F4BM245 (PTFE + Fiberglass + ED Copper Foil) |
| Layer count | 2-layer rigid PCB |
| Board dimensions | 100mm x 80mm = 1 PCS, ±0.15mm |
| Minimum Trace/Space | 4/5 mils |
| Minimum Hole Size | 0.3mm |
| Blind vias | No |
| Finished board thickness | 0.6mm |
| Finished Cu weight | 1 oz (35 μm / 1.4 mils) all layers |
| Via plating thickness | 20 μm |
| Surface finish | Immersion Gold |
| Top Silkscreen | No |
| Bottom Silkscreen | No |
| Top Solder Mask | No |
| Bottom Solder Mask | No |
| 100% Electrical test | Used prior to shipment |
Note: The following thicknesses can be produced as either total thickness including copper or dielectric thickness. Please specify when ordering.
| Standard Dielectric Thicknesses (mm) | 0.1 (3.9mil), 0.127 (5mil), 0.2, 0.25, 0.5, 0.508, 0.762, 0.8, 1.0, 1.5, 1.524, 1.575, 2.0, 2.5, 3.0, 4.0, 5.0, 6.0, 8.0, 10.0, 12.0 |
| Thickness Tolerances (mm) | 0.1mm: ±0.01, 0.127mm: ±0.01, 0.2mm: ±0.02, 0.25mm: ±0.02, 0.5mm: ±0.04, 0.508mm: ±0.04, 0.762mm: ±0.05, 0.8mm: ±0.05, 1.0mm: ±0.05, 1.5mm: ±0.06, 1.524mm: ±0.06, 1.575mm: ±0.06, 2.0mm: ±0.08, 2.5mm: ±0.08, 3.0mm: ±0.09, 4.0mm: ±0.1, 5.0mm: ±0.1, 6.0mm: ±0.12, 8.0mm: ±0.15, 10.0mm: ±0.18, 12.0mm: ±0.2 |
| Standard Panel Sizes | 460×610mm, 500×600mm, 850×1200mm, 914×1220mm, 1000×1200mm |
| Custom Panel Sizes | 300×250mm, 350×380mm, 500×500mm, 840×840mm, 1000×1500mm |
| F4BM Claddings (ED Copper) | 0.5oz (0.018mm), 1oz (0.035mm), 1.5oz (0.05mm), 2oz (0.07mm) |
| F4BME Claddings (RTF Copper) | 0.5oz (0.018mm), 1oz (0.035mm) |
| DK Options (F4B Series) | 2.17 ~ 3.0 (customizable) |
| Metal Base Options | F4BM***-AL (Aluminum base), F4BM***-CU (Copper base) for shielding/heat dissipation |
Note: For thicknesses ≥4.0mm or ≤0.2mm, panel size cannot exceed 500×610mm.
Layer stack-up
- Layer: Copper_layer_1 (Top), Material: Copper (ED), Thickness: 35 μm (1 oz)
- Layer: Dielectric, Material: F4BM245 Core, Thickness: 0.508 mm (20mil)
- Layer: Copper_layer_2 (Bottom), Material: Copper (ED), Thickness: 35 μm (1 oz)
PCB Statistics
- Components: 24
- Total Pads: 36
- Thru Hole Pads: 21
- Top SMT Pads: 15
- Bottom SMT Pads: 0
- Vias: 28
- Nets: 2
Application areas
- Microwave, RF, and radar systems
- Phase shifters and passive components
- Power dividers, couplers, and combiners
- Feed networks and phased array antennas
- Phase-sensitive antennas
- Satellite communications and base station antennas
- High-frequency RF and microwave circuits
- Microwave, RF, and radar systems
- Phase shifters and passive components
- Power dividers, couplers, and combiners
- Feed networks and phased array antennas
- Phase-sensitive antennas
- Satellite communications and base station antennas
- High-frequency RF and microwave circuits
Properties
F4BM245 Typical Properties
| Property | F4BM245 | Dir. | Units | Condition | Test Method |
|---|---|---|---|---|---|
| Dielectric Constant (Typical), 10 GHz | 2.45 | — | — | 10 GHz | — |
| Dk Tolerance | ±0.05 | — | — | — | — |
| Dissipation Factor, 10 GHz | 0.0012 | — | — | 10 GHz | — |
| Dissipation Factor, 20 GHz | 0.0017 | — | — | 20 GHz | — |
| Thermal Coefficient of Dk | -120 | — | ppm/°C | -55 to 150°C | — |
| Peel Strength (F4BM, 1oz ED) | >1.8 | — | N/mm | 1 oz ED copper | — |
| Peel Strength (F4BME, 1oz RTF) | >1.6 | — | N/mm | 1 oz RTF copper | — |
| Volume Resistivity | ≥6×10⁶ | — | MΩ·cm | Room temp | — |
| Surface Resistivity | ≥1×10⁶ | — | MΩ | Room temp | — |
| Dielectric Strength (Z) | >25 | — | kV/mm | 5 kV, 500V/s | — |
| Dielectric Breakdown (X/Y) | >32 | — | kV | 5 kV, 500V/s | — |
| CTE (X, Y) | 20, 25 | X,Y | ppm/°C | -55 to 288°C | — |
| CTE (Z) | 187 | Z | ppm/°C | -55 to 288°C | — |
| Moisture Absorption | ≤0.08 | — | % | 20±2°C, 24 hrs | — |
| Density | 2.22 | — | g/cm³ | Room temp | — |
| Thermal Conductivity (Z) | 0.30 | Z | W/(m·K) | — | — |
| Continuous Operating Temp | -55 to +260 | — | °C | — | — |
| Flammability | V-0 | — | — | — | UL94 |
Quality Assurance
- Type of artwork supplied: Gerber RS-274-X
- Accepted standard: IPC-Class-2
- Availability: Worldwide
- 100% Electrical test prior to shipment
- Type of artwork supplied: Gerber RS-274-X
- Accepted standard: IPC-Class-2
- Availability: Worldwide
- 100% Electrical test prior to shipment
F4B Series Aluminum/Copper Base Option
The F4BM and F4BME series can also be provided with an aluminum or copper base, where one side of the dielectric layer is covered with copper foil and the other side is laminated with copper or aluminum for shielding or heat dissipation purposes. Model designation: F4BM***-AL, F4BME***-AL, F4BM***-CU, F4BME***-CU.
| Model | Metal Base | Specific Gravity | Thermal Conductivity | CTE | Available Metal Thickness | Thickness Tolerance | Available Sizes |
|---|---|---|---|---|---|---|---|
| F4BM***-CU / F4BME***-CU | Copper (Purple/Brass) | 8.9 | 380 W/(M·K) | 17 ppm/°C | 0.48, 0.98, 1.48, 1.98, 2.98, 3.98mm (other thicknesses available upon request) | +0.02, -0.05 | 460×610mm, 460×305mm (other sizes available upon request) |
| F4BM***-AL / F4BME***-AL | Aluminum | 2.7 | 180 W/(M·K) | 24 ppm/°C | 0.48, 0.98, 1.48, 1.98, 2.98, 3.98mm (other thicknesses available upon request) | +0.02, -0.05 | 460×610mm, 460×305mm (other sizes available upon request) |
Example: F4BM245-AL represents F4BM245 with aluminum base. F4BM245-CU represents F4BM245 with copper base.
Data Source Notes
- Dielectric Constant is tested in the Z-direction of the material using GB/T 12636-1990 or IPC-TM-650 2.5.5.5 Stripline method.
- Other properties are tested using or referencing IPC-TM-650 or GBT4722-2017 standard test methods.
- All test data are typical measurement values intended to assist customers in material selection. They do not constitute any express or implied warranty and do not guarantee performance in specific applications. Customers are responsible for verifying the suitability of Wangling materials for each application.
Dielectric Constant is tested in the Z-direction of the material using GB/T 12636-1990 or IPC-TM-650 2.5.5.5 Stripline method.
Other properties are tested using or referencing IPC-TM-650 or GBT4722-2017 standard test methods.
All test data are typical measurement values intended to assist customers in material selection. They do not constitute any express or implied warranty and do not guarantee performance in specific applications. Customers are responsible for verifying the suitability of Wangling materials for each application.
Tell us the board. We answer within 4 hours.
Large Gerber files are easier by email — this form gets the conversation started with the right engineer.
Send requestOr email your files torfq@bichengcircuits.com
