BICHENGPCBBicheng Technologies Limited

Wangling TP2000 2-Layer 6.1mm Bare Copper PCB for High-DK RF & Antenna Applications

Custom product. Images and specifications are for reference only; the confirmed drawing governs.

Brief introduction

TP2000 material is a unique high frequency thermoplastic material in the industry. The dielectric layer of TP based sheets is composed of ceramic and polyphenylene oxide (PPO) resin, with no glass fiber reinforcement, engineered for high-frequency RF and microwave applications. It features an ultra-high dielectric constant, ultra-low dissipation factor, and excellent thermal stability, making it ideal for designs requiring compact size and high signal integrity. The material operates reliably across a wide temperature range and is easy to machine, supporting standard PCB fabrication processes.

This 2-layer rigid PCB is constructed entirely with TP2000 as the core material, providing exceptional signal integrity, compact design capability due to high DK, and thermal stability for demanding RF, microwave, and aerospace applications.

Thermal Coefficient of DK (TCDK): -55 ppm/°C

Coefficient of Thermal Expansion (CTE): X=35 ppm/°C, Y=35 ppm/°C, Z=40 ppm/°C

Operating Temperature Range: -100°C to +150°C

High mechanical strength and dimensional stability

Easy machinability (drilling, cutting, engraving)

Compatible with standard PCB assembly processes

Ultra-high dielectric constant enables circuit miniaturization

Ultra-low dissipation factor for excellent signal integrity

Excellent thermal stability across wide temperature range (-100°C to +150°C)

No glass fiber reinforcement – homogeneous dielectric properties

Excellent radiation resistance for aerospace and defense applications

Easy machinability – can be drilled, cut, and engraved

Copper_layer_1 – 35 μm TP2000 core – 6 mm Copper_layer_2 – 35 μm

Components: 24 Total Pads: 37 Thru Hole Pads: 18 Top SMT Pads: 19 Bottom SMT Pads: 0 Vias: 12 Nets: 2

High-frequency RF and microwave circuits

Antenna systems (including phased array antennas)

Radar systems (automotive, aerospace, defense)

Artwork supplied: Gerber RS-274-X Accepted standard: IPC-Class-2 Availability: Worldwide

9.TP2000 Microwave Composite Copper-Clad Laminate – Product Introduction

TP material is a unique high frequency thermoplastic material in the industry. The dielectric layer of TP based sheets is composed of ceramic and polyphenylene oxide (PPO) resin, with no glass fiber reinforcement. The dielectric constant is precisely adjusted by controlling the ratio between ceramic and PPO resin. The production process is special, resulting in excellent dielectric properties and high reliability.

TP refers to unclad smooth surface material, TP-1 refers to single-sided copper clad material, and TP-2 refers to double-sided copper clad material.

Dielectric constant can be arbitrarily selected within the range of 3 to 25 according to circuit requirements, with stable performance. Common dielectric constants include 3.0, 4.4, 6.0, 6.15, 9.2, 9.6, 10.2, 11, 16, 20. Low dielectric loss – loss increases with frequency, but changes little within 10GHz.

Long-term operating temperature range: -100°C to +150°C. Excellent low-temperature resistance. When temperature exceeds 180°C, the material may deform, copper foil may detach, and electrical properties may change significantly.

Minimum thickness 0.5mm, rich thickness options, customizable.

Ideal material for Beidou navigation, missile-borne systems, fuzes, and miniaturized antennas.

Adhesion between copper foil and dielectric is stronger than vacuum coating on ceramic substrates. Material is easy to machine – can be drilled, turned, ground, sheared, engraved, etc. – which ceramic substrates cannot match.

Easy PCB processing using standard thermoplastic material processing methods. High yield rate and significantly lower processing cost compared to ceramic substrates. Due to material characteristics, multi-layer processing is generally not recommended. If multi-layer processing is required, please select low-temperature bonding sheets and fully consider feasibility.

Material is not suitable for 260°C thermal shock testing and cannot undergo wave soldering. Soldering recommendation: manual soldering with constant temperature iron. Reflow soldering is generally not recommended. If reflow soldering is required, the maximum set temperature should not exceed 200°C, and feasibility and stability should be fully considered.

13.Standard Thicknesses, Panel Sizes & Claddings

Application areas

  • Dielectric Constant (DK): 20 at 5GHz
  • Dissipation Factor (Df): 0.002 at 5GHz
  • Thermal Coefficient of DK (TCDK): -55 ppm/°C
  • Coefficient of Thermal Expansion (CTE): X=35 ppm/°C, Y=35 ppm/°C, Z=40 ppm/°C
  • Operating Temperature Range: -100°C to +150°C
  • High mechanical strength and dimensional stability
  • Excellent radiation resistance
  • Easy machinability (drilling, cutting, engraving)
  • Compatible with standard PCB assembly processes
  • UL 94-V0 flammability rating
TP2000 PCB 6mm Pure Gold
CCL 140 TP2000

PCB specifications

Base materialTP2000
Layer count2 layers
Board dimensions85mm x 85mm = 1PCS, +/- 0.15mm
Minimum Trace/Space6/7 mils
Minimum Hole Size0.35mm
Blind viasNo
Finished board thickness6.1mm
Finished Cu weight1 oz (1.4 mils) outer layers
Via plating thickness20 μm
Surface finishBare copper
Top SilkscreenNo
Bottom SilkscreenNo
Top Solder MaskNo
Bottom Solder MaskNo
100% Electrical testUsed prior to shipment

Tell us the board. We answer within 4 hours.

Large Gerber files are easier by email — this form gets the conversation started with the right engineer.

Send request

Or email your files torfq@bichengcircuits.com