BICHENGPCBBicheng Technologies Limited

Rogers 60mil 1.524mm TMM10 Microwave PCBs with Immersion Gold for Patch Antennas

(Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference)

Brief introduction

Rogers 60mil 1.524mm TMM10 Microwave PCBs with Immersion Gold for Patch Antennas. These laminates combine the advantages of both ceramic and traditional PTFE microwave circuit laminates without needing specialized production techniques.

TMM10 laminates feature an exceptionally low thermal coefficient of dielectric constant, typically less than 30 ppm/°C. The isotropic coefficients of thermal expansion are closely matched to copper, facilitating the production of high-reliability plated-through holes and minimizing etch shrinkage. Additionally, the thermal conductivity of TMM10 laminates is approximately twice that of traditional PTFE/ceramic laminates, enhancing heat dissipation.

As TMM10 laminates are based on thermoset resins, they do not soften when heated. This characteristic allows for wire bonding of component leads to circuit traces without concerns about pad lifting or substrate deformation.

Product images

TMM10 PCB

Application areas

  • Chip Testers
  • Dielectric Polarizers and Lenses
  • Filters and Couplers
  • Global Positioning Systems Antennas
  • Patch Antennas
  • Power Amplifiers and Combiners
  • RF and Microwave Circuitry
  • Satellite Communication Systems

Our PCB Capability

PCB Capability (TMM10)

PCB Material:Ceramic, Hydrocarbon, Thermoset Polymer Composites
Designation:TMM10
Dielectric constant:9.20 ± 0.23
Layer count:Single Layer, Double Layer, Multilayer, Hybrid PCB
Copper weight:1oz, 2oz
PCB thickness:15mil,20mil,25mil,30mil,50mil,60mil,75mil,100mil,125mil,150mil,200mil,250mil,275mil,300mil,500mil
PCB size:≤400mm X 500mm
Solder mask:Green, Black, Blue, Yellow, Red etc.
Surface finish:Bare copper, HASL, ENIG, Immersion Silver, Immersion Tin, ENEPIG, Pure Gold, OSP etc.

Properties

TMM 10 Typical Properties

PropertyTMM 10Dir.UnitsConditionTest Method
Dielectric Constant (Process)9.20 ± 0.23Z—10 GHzIPC-TM-650 2.5.5.5
Dielectric Constant (Design)9.8Z——Microstrip
Dissipation Factor0.0022Z—10 GHzIPC-TM-650 2.5.5.5
Thermal Coefficient of Dk-38—ppm/°C-50 to 150°CIPC-TM-650 2.5.5.5
Volume Resistivity2 × 10⁸—MΩ·cmCondition AASTM D257
Surface Resistivity4 × 10⁷—MΩCondition AASTM D257
Moisture Absorption0.09—%D24/50ASTM D570
Thermal Conductivity0.76ZW/(m·K)50°CASTM D5470
CTE (X)21Xppm/°C-55 to 288°CIPC-TM-650 2.4.41
CTE (Y)21Yppm/°C-55 to 288°CIPC-TM-650 2.4.41
CTE (Z)20Zppm/°C-55 to 288°CIPC-TM-650 2.4.41
Copper Peel Strength5.0 (0.9)—lbs/in (N/mm)1 oz ED foilIPC-TM-650 2.4.8
Density2.8—g/cm³—ASTM D792
FlammabilityNon-FR———UL94

Tell us the board. We answer within 4 hours.

Large Gerber files are easier by email — this form gets the conversation started with the right engineer.

Send request

Or email your files torfq@bichengcircuits.com