Rogers 200mil 5.08mm TMM10 Microwave PCBs with ENIG for Patch Antennas
(Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference)
Brief introduction
Rogers 200mil 5.08mm TMM10 Microwave PCBs with ENIG for Patch Antennas. TMM10 thermoset microwave materials offer the benefits of both PTFE and ceramic based substrates, but is not limited by the same mechanical properties and production techniques.
TMM10 laminates feature an exceptionally low thermal coefficient of dielectric constant, typically less than 30 ppm/°C. The isotropic coefficients of thermal expansion are closely matched to copper, facilitating the production of high-reliability plated-through holes and minimizing etch shrinkage. Additionally, the thermal conductivity of TMM10 laminates is approximately twice that of traditional PTFE/ceramic laminates, enhancing heat dissipation.
As TMM10 laminates are based on thermoset resins, they do not soften when heated. This characteristic allows for wire bonding of component leads to circuit traces without concerns about pad lifting or substrate deformation.
Technical features & benefits
- Dielectric Constant (Dk) of 9.20 +/- .230
- Dissipation factor of .0022 at 10GHz
- Thermal coefficient of Dk of -38 ppm/°K
- Coefficient of thermal expansion matched to copper
- Decomposition Temperature (Td) of 425 °C TGA
- Coefficient of Thermal Expansion - x y z : 21ppm/K, 21ppm/K, 20ppm/K
- Thermal Conductivity of 0.76W/mk
- Available in a thickness range of .0015 to .500 inches +/- .0015"
- Mechanical properties resist creep and cold flow
- Resistant to process chemicals, reducing damage during fabrication
- Material does not require a sodium napthanate treatment prior to electroless plating
- Based on a thermoset resin, allowing for reliable wire-bonding
- Wide range of dielectric constants — ideal for single material systems on a wide variety of applications
- Exceptional mechanical properties — resist creep and cold flow
- High reliability of plated through holes
- Resistant to process chemicals — reduces damage to material during fabrication and assembly processes
- Thermoset resin — reliable wirebonding
- No specialized production techniques required
- TMM10 and 10 laminates can replace alumina substrates
Product images
PCB specifications
| Base material | TMM10 |
| Layer count | Double sided |
| Board dimensions | 63.9mm x 48mm = 1 PCS, ±0.15mm |
| Minimum Trace/Space | 4/7 mils |
| Minimum Hole Size | 0.25mm |
| Blind vias | No |
| Finished board thickness | 5.1mm |
| Finished Cu weight | 1 oz (1.4 mils) outer layers |
| Via plating thickness | 20 μm |
| Surface finish | ENIG |
| Top Silkscreen | No |
| Bottom Silkscreen | No |
| Top Solder Mask | No |
| Bottom Solder Mask | No |
| 100% Electrical test | Used prior to shipment |
| Standard Thicknesses / Claddings | Standard Panel Sizes | |
| 0.015" (0.381mm) +/- 0.0015" 0.025" (0.635mm) +/- 0.0015" 0.030" (0.762mm) +/- 0.0015" 0.050" (1.270mm) +/- 0.0015" 0.060" (1.524mm) +/- 0.0015" 0.075" (1.900mm) +/- 0.0015" | 0.100" (2.500mm) +/- 0.0015" 0.125" (3.175mm) +/- 0.0015" 0.150" (3.810mm) +/- 0.0015" 0.200" (5.080mm) +/- 0.0015" 0.250" (6.350mm) +/- 0.0015" 0.500" (12.70mm) +/- 0.0015" | 18"X 12" (457mm X 305mm) 18"X 24" (457mm X 610mm) *Additional panel sizes available |
| Electrodeposited Copper Foil ½ oz. (18um) HH/HH 1 oz. (35um) H1/H1 *Additional claddings such as heavy metal and unclad are available | ||
Layer stack-up
Layer: Copper_layer_1 (Top), Material: Copper, Thickness: 35 μm
Layer: Dielectric, Material: Rogers TMM10 Core, Thickness: 5.08 mm (200mil)
Layer: Copper_layer_2 (Bottom), Material: Copper, Thickness: 35 μm
PCB Statistics
- Components: 26
- Total Pads: 38
- Thru Hole Pads: 21
- Top SMT Pads: 17
- Bottom SMT Pads: 0
- Vias: 13
- Nets: 2
Application areas
- Chip Testers
- Dielectric Polarizers and Lenses
- Filters and Couplers
- Global Positioning Systems Antennas
- Patch Antennas
- Power Amplifiers and Combiners
- RF and Microwave Circuitry
- Satellite Communication Systems
- Type of artwork supplied: Gerber RS-274-X
- Quality standard: IPC-Class-2
- Availability: worldwide
Our PCB Capability
PCB Capability (TMM10)
| PCB Material: | Ceramic, Hydrocarbon, Thermoset Polymer Composites |
| Designation: | TMM10 |
| Dielectric constant: | 9.20 ± 0.23 |
| Layer count: | Single Layer, Double Layer, Multilayer, Hybrid PCB |
| Copper weight: | 1oz, 2oz |
| PCB thickness: | 15mil,20mil,25mil,30mil,50mil,60mil,75mil,100mil,125mil,150mil,200mil,250mil,275mil,300mil,500mil |
| PCB size: | ≤400mm X 500mm |
| Solder mask: | Green, Black, Blue, Yellow, Red etc. |
| Surface finish: | Bare copper, HASL, ENIG, Immersion Silver, Immersion Tin, ENEPIG, Pure Gold, OSP etc. |
Properties
TMM 10 Typical Properties
| Property | TMM 10 | Dir. | Units | Condition | Test Method |
|---|---|---|---|---|---|
| Dielectric Constant (Process) | 9.20 ± 0.23 | Z | — | 10 GHz | IPC-TM-650 2.5.5.5 |
| Dielectric Constant (Design) | 9.8 | Z | — | — | Microstrip |
| Dissipation Factor | 0.0022 | Z | — | 10 GHz | IPC-TM-650 2.5.5.5 |
| Thermal Coefficient of Dk | -38 | — | ppm/°C | -50 to 150°C | IPC-TM-650 2.5.5.5 |
| Volume Resistivity | 2 × 10⁸ | — | MΩ·cm | Condition A | ASTM D257 |
| Surface Resistivity | 4 × 10⁷ | — | MΩ | Condition A | ASTM D257 |
| Moisture Absorption | 0.09 | — | % | D24/50 | ASTM D570 |
| Thermal Conductivity | 0.76 | Z | W/(m·K) | 50°C | ASTM D5470 |
| CTE (X) | 21 | X | ppm/°C | -55 to 288°C | IPC-TM-650 2.4.41 |
| CTE (Y) | 21 | Y | ppm/°C | -55 to 288°C | IPC-TM-650 2.4.41 |
| CTE (Z) | 20 | Z | ppm/°C | -55 to 288°C | IPC-TM-650 2.4.41 |
| Copper Peel Strength | 5.0 (0.9) | — | lbs/in (N/mm) | 1 oz ED foil | IPC-TM-650 2.4.8 |
| Density | 2.8 | — | g/cm³ | — | ASTM D792 |
| Flammability | Non-FR | — | — | — | UL94 |
Notes
Notes: ASTM E831 corresponds to IPC-TM-650, method 2.4.41 * estimated
Typical values are a representation of an average value for the population of the property. For specification values contact Rogers Corporation.
(1) Prolonged exposure in an oxidative environment may cause changes to the dielectric properties of hydrocarbon based materials. The rate of change increases at higher temperatures and is highly dependent on the circuit design. Although Rogers' high frequency materials have been used successfully in innumerable applications and reports of oxidation resulting in performance problems are extremely rare, Rogers recommends that the customer evaluate each material and design combination to determine fitness for use over the entire life of the end product.
(2) The design Dk is an average number from several different tested lots of material and on the most common thicknesses. If more detailed information is required, please contact Rogers Corporation. Refer to Rogers' technical paper "Dielectric Properties of High Frequency Materials" available on www.rogerscorp.com/acm.
(3) Method 2.5.5.6.
Tell us the board. We answer within 4 hours.
Large Gerber files are easier by email — this form gets the conversation started with the right engineer.
Send requestOr email your files torfq@bichengcircuits.com
