BICHENGPCBBicheng Technologies Limited

F4BME220 2-Layer 3.9mil Immersion Gold High Frequency PCB for RF & Radar Applications

(Note: Printed Circuit Boards are custom-made products. Images and parameters are for reference only.)

Brief introduction

F4BME series laminates are made by scientifically formulating and strictly pressing a combination of fiberglass cloth, polytetrafluoroethylene resin, and polytetrafluoroethylene film. Its electrical performance is improved compared to F4B, mainly due to a wider range of dielectric constants, lower dielectric loss, increased insulation resistance, and improved stability. It can replace similar foreign products.

F4BM and F4BME have the same dielectric layer, but use different copper foils: F4BM uses ED copper foil, suitable for applications without PIM requirements; F4BME uses reverse-treated RTF copper foil, offering excellent PIM performance, more precise circuit control, and lower conductor loss.

This 2-layer rigid PCB is constructed entirely with F4BME220 as the core material at 3.9mil (0.1mm) dielectric thickness, with immersion gold surface finish, white top silkscreen, green top solder mask, and 1oz RTF copper on both sides. Its DK of 2.2 offers excellent high-frequency performance, making it ideal for demanding applications such as microwave, RF, radar, phase shifters, power dividers, couplers, phased array antennas, satellite communications, and base station antennas.

Technical features & benefits

  • Dielectric Constant (DK): 2.2 ± 0.04 at 10GHz
  • DK Range: 2.17 ~ 3.0 optional, DK customizable
  • Dissipation Factor (Df): 0.001 at 10GHz / 0.0014 at 20GHz
  • Low loss performance
  • TCDK: -142 ppm/°C (-55°C to 150°C)
  • Excellent PIM Value: ≤ -159 dBc (with RTF copper foil)
  • Peel Strength (1oz F4BME): >1.6 N/mm
  • Volume Resistivity: ≥6×10⁶ MΩ·cm
  • Surface Resistivity: ≥1×10⁶ MΩ
  • Electrical Strength (Z direction): >23 KV/mm
  • Breakdown Voltage (XY direction): >30 KV
  • CTE (XY direction): 25/34 ppm/°C (-55°C to 288°C)
  • CTE (Z direction): 240 ppm/°C (-55°C to 288°C)
  • Thermal Conductivity: 0.24 W/(M·K)
  • Density: 2.18 g/cm³
  • Moisture Absorption: ≤0.08%
  • Long-term Operating Temperature: -55°C to +260°C
  • UL 94 V-0 Flammability Rating
  • Irradiation resistance and low outgassing
  • Commercialization, mass production, high cost-performance
  • Stable DK (2.2±0.04) — Consistent impedance control for high-frequency designs
  • Ultra-Low Df (0.001 @ 10GHz) — Excellent signal integrity with minimal insertion loss
  • Excellent PIM Performance (≤ -159 dBc) — Ideal for low intermodulation applications
  • RTF Copper Foil — More precise circuit control and lower conductor loss
  • Wider DK Range (2.17 ~ 3.0) — Flexible design options, DK customizable
  • Irradiation Resistance & Low Outgassing — Suitable for aerospace and defense applications
  • Commercialization & High Cost-Performance — Mass production ready
  • Immersion Gold Finish — Excellent solderability, corrosion resistance, and wire bondability
  • DK 2.2 ± 0.04 @ 10GHz:Stable dielectric constant for consistent impedance control
  • Df 0.001 @ 10GHz / 0.0014 @ 20GHz:Ultra-low loss for high-frequency RF and microwave designs
  • PIM ≤ -159 dBc (with RTF copper):Excellent low intermodulation performance
  • RTF copper foil:More precise circuit control, lower conductor loss
  • DK 2.17 ~ 3.0 optional, customizable:Flexible design options
  • Low CTE (25/34 ppm/°C XY direction):Excellent dimensional stability
  • UL 94 V-0 Rating:Flame retardant safety standard
  • Irradiation resistance & low outgassing:Ideal for aerospace and defense applications
  • Immersion Gold finish:Excellent solderability, corrosion resistance, wire bondability

Product images

F4BME220 PCB
F4BME220 Material

PCB specifications

Base materialWangling F4BME220 (PTFE + Fiberglass + RTF Copper Foil)
Layer count2-layer rigid PCB
Board dimensions79mm x 65.3mm = 1 PCS, ±0.15mm
Minimum Trace/Space5/8 mils
Minimum Hole Size0.25mm
Blind viasNo
Finished board thickness0.1mm (dielectric thickness)
Finished Cu weight1 oz (35 μm / 1.4 mils) all layers
Via plating thickness20 μm
Surface finishImmersion Gold
Top SilkscreenWhite
Bottom SilkscreenNo
Top Solder MaskGreen
Bottom Solder MaskNo
100% Electrical testUsed prior to shipment

Note: The following thicknesses can be produced as either total thickness including copper or dielectric thickness. Please specify when ordering.

Standard Dielectric Thicknesses (mm)0.1 (3.9mil), 0.127 (5mil), 0.2, 0.25, 0.5, 0.508, 0.762, 0.8, 1.0, 1.5, 1.524, 1.575, 2.0, 2.5, 3.0, 4.0, 5.0, 6.0, 8.0, 10.0, 12.0
Thickness Tolerances (mm)0.1mm: ±0.01, 0.127mm: ±0.01, 0.2mm: ±0.02, 0.25mm: ±0.02, 0.5mm: ±0.04, 0.508mm: ±0.04, 0.762mm: ±0.05, 0.8mm: ±0.05, 1.0mm: ±0.05, 1.5mm: ±0.06, 1.524mm: ±0.06, 1.575mm: ±0.06, 2.0mm: ±0.08, 2.5mm: ±0.08, 3.0mm: ±0.09, 4.0mm: ±0.1, 5.0mm: ±0.1, 6.0mm: ±0.12, 8.0mm: ±0.15, 10.0mm: ±0.18, 12.0mm: ±0.2
Standard Panel Sizes460×610mm, 500×600mm, 850×1200mm, 914×1220mm, 1000×1200mm
Custom Panel Sizes300×250mm, 350×380mm, 500×500mm, 840×840mm, 1000×1500mm
F4BM Claddings (ED Copper)0.5oz (0.018mm), 1oz (0.035mm), 1.5oz (0.05mm), 2oz (0.07mm)
F4BME Claddings (RTF Copper)0.5oz (0.018mm), 1oz (0.035mm)
DK Options (F4BME Series)2.17 ~ 3.0 (customizable)
Metal Base OptionsF4BME***-AL (Aluminum base), F4BME***-CU (Copper base) for shielding/heat dissipation

Note: For thicknesses ≥4.0mm or ≤0.2mm, panel size cannot exceed 500×610mm.

Layer stack-up

  • Layer: Copper_layer_1 (Top), Material: Copper (RTF), Thickness: 35 μm (1 oz)
  • Layer: Dielectric, Material: F4BME220 Core, Thickness: 0.1 mm (3.9mil) — dielectric thickness
  • Layer: Copper_layer_2 (Bottom), Material: Copper (RTF), Thickness: 35 μm (1 oz)

PCB Statistics

  • Components: 23
  • Total Pads: 26
  • Thru Hole Pads: 14
  • Top SMT Pads: 12
  • Bottom SMT Pads: 0
  • Vias: 37
  • Nets: 2

7. Wangling F4BME220 Material – Product Introduction

This product is made by scientifically formulating and strictly pressing a combination of fiberglass cloth, polytetrafluoroethylene resin, and polytetrafluoroethylene film. Its electrical performance is improved compared to F4B, mainly due to a wider range of dielectric constants, lower dielectric loss, increased insulation resistance, and improved stability. It can replace similar foreign products.

F4BM and F4BME have the same dielectric layer, but use different copper foils: F4BM uses ED copper foil, suitable for applications without PIM requirements; F4BME uses reverse-treated RTF copper foil, offering excellent PIM performance, more precise circuit control, and lower conductor loss.

F4BM and F4BME precisely adjust the dielectric constant by adjusting the ratio of PTFE to fiberglass cloth, achieving low loss while enhancing dimensional stability. The higher the dielectric constant, the higher the fiberglass ratio, resulting in better dimensional stability, lower CTE, better temperature stability, though dielectric loss increases accordingly.

F4BME220 features a dielectric constant of 2.2±0.04 at 10GHz, ultra-low dissipation factor of 0.001 at 10GHz and 0.0014 at 20GHz, and excellent thermal stability. The material operates reliably across a wide temperature range from -55°C to +260°C and is suitable for mass production with high cost-performance.

Application areas

  • Microwave, RF, and radar systems
  • Phase shifters and passive components
  • Power dividers, couplers, and combiners
  • Feed networks and phased array antennas
  • Satellite communications and base station antennas
  • High-frequency RF and microwave circuits
  • Microwave, RF, and radar systems
  • Phase shifters and passive components
  • Power dividers, couplers, and combiners
  • Feed networks and phased array antennas
  • Satellite communications and base station antennas
  • High-frequency RF and microwave circuits

Properties

F4BM / F4BME Series Typical Properties

PropertyF4BM217F4BM220F4BM233F4BM245F4BM255F4BM265F4BM275F4BM294F4BM300Dir.UnitsConditionTest Method
Dielectric Constant (Typical), 10 GHz2.172.202.332.452.552.652.752.943.00——10 GHz—
Dk Tolerance±0.04±0.04±0.04±0.05±0.05±0.05±0.05±0.06±0.06————
Dissipation Factor, 10 GHz0.0010.0010.00110.00120.00130.00130.00150.00160.0017——10 GHz—
Dissipation Factor, 20 GHz0.00140.00140.00150.00170.00180.00190.00210.00230.0025——20 GHz—
Thermal Coefficient of Dk-150-142-130-120-110-100-92-85-80—ppm/°C-55 to 150°C—
Peel Strength (F4BM, 1oz ED)>1.8>1.8>1.8>1.8>1.8>1.8>1.8>1.8>1.8—N/mm1 oz ED copper—
Peel Strength (F4BME, 1oz RTF)>1.6>1.6>1.6>1.6>1.6>1.6>1.6>1.6>1.6—N/mm1 oz RTF copper—
Volume Resistivity≥6×10⁶≥6×10⁶≥6×10⁶≥6×10⁶≥6×10⁶≥6×10⁶≥6×10⁶≥6×10⁶≥6×10⁶—MΩ·cmRoom temp—
Surface Resistivity≥1×10⁶≥1×10⁶≥1×10⁶≥1×10⁶≥1×10⁶≥1×10⁶≥1×10⁶≥1×10⁶≥1×10⁶—MΩRoom temp—
Dielectric Strength (Z)>23>23>23>25>25>25>28>30>30—kV/mm5 kV, 500V/s—
Dielectric Breakdown (X/Y)>30>30>32>32>34>34>35>36>36—kV5 kV, 500V/s—
CTE (X, Y)25, 3425, 3422, 3020, 2516, 2114, 1714, 1612, 1512, 15X,Yppm/°C-55 to 288°C—
CTE (Z)2402402051871731421129895Zppm/°C-55 to 288°C—
Moisture Absorption≤0.08≤0.08≤0.08≤0.08≤0.08≤0.08≤0.08≤0.08≤0.08—%20±2°C, 24 hrs—
Density2.172.182.202.222.252.252.282.292.29—g/cm³Room temp—
Thermal Conductivity (Z)0.240.240.280.300.330.360.380.410.42ZW/(m·K)——
Continuous Operating Temp-55 to +260-55 to +260-55 to +260-55 to +260-55 to +260-55 to +260-55 to +260-55 to +260-55 to +260—°C——
FlammabilityV-0V-0V-0V-0V-0V-0V-0V-0V-0———UL94

Quality Assurance

  • Type of artwork supplied: Gerber RS-274-X
  • Accepted standard: IPC-Class-2
  • Availability: Worldwide
  • 100% Electrical test prior to shipment
  • Type of artwork supplied: Gerber RS-274-X
  • Accepted standard: IPC-Class-2
  • Availability: Worldwide
  • 100% Electrical test prior to shipment

F4BME Series Aluminum/Copper Base Option

The F4BM and F4BME series can also be provided with an aluminum or copper base, where one side of the dielectric layer is covered with copper foil and the other side is laminated with copper or aluminum for shielding or heat dissipation purposes. Model designation: F4BM***-AL, F4BME***-AL, F4BM***-CU, F4BME***-CU.

ModelMetal BaseSpecific GravityThermal ConductivityCTEAvailable Metal ThicknessThickness ToleranceAvailable Sizes
F4BM***-CU / F4BME***-CUCopper (Purple/Brass)8.9380 W/(M·K)17 ppm/°C0.48, 0.98, 1.48, 1.98, 2.98, 3.98mm (other thicknesses available upon request)+0.02, -0.05460×610mm, 460×305mm (other sizes available upon request)
F4BM***-AL / F4BME***-ALAluminum2.7180 W/(M·K)24 ppm/°C0.48, 0.98, 1.48, 1.98, 2.98, 3.98mm (other thicknesses available upon request)+0.02, -0.05460×610mm, 460×305mm (other sizes available upon request)

Example: F4BME220-AL represents F4BME220 with aluminum base. F4BME220-CU represents F4BME220 with copper base.

Data Source Notes

  • Dielectric Constant is tested in the Z-direction of the material using GB/T 12636-1990 or IPC-TM-650 2.5.5.5 Stripline method.
  • Other properties are tested using or referencing IPC-TM-650 or GBT4722-2017 standard test methods.
  • All test data are typical measurement values intended to assist customers in material selection. They do not constitute any express or implied warranty and do not guarantee performance in specific applications. Customers are responsible for verifying the suitability of Wangling materials for each application.

Dielectric Constant is tested in the Z-direction of the material using GB/T 12636-1990 or IPC-TM-650 2.5.5.5 Stripline method.

Other properties are tested using or referencing IPC-TM-650 or GBT4722-2017 standard test methods.

All test data are typical measurement values intended to assist customers in material selection. They do not constitute any express or implied warranty and do not guarantee performance in specific applications. Customers are responsible for verifying the suitability of Wangling materials for each application.

Tell us the board. We answer within 4 hours.

Large Gerber files are easier by email — this form gets the conversation started with the right engineer.

Send request

Or email your files torfq@bichengcircuits.com