BICHENGPCBBicheng Technologies Limited

HDI Hybrid PCB 8-Layer 1.5mm RO4003C S1000-2M Advanced Impedance Control for RF and Microwave Circuits

Custom product. Images and specifications are for reference only; the confirmed drawing governs.

Brief introduction

Rogers RO4003C materials are proprietary woven glass reinforced hydrocarbon/ceramics that combine the electrical performance of PTFE/woven glass with the manufacturability of epoxy/glass. This design offers superior high-frequency performance and cost-effective circuit fabrication. The result is a low-loss material that can be fabricated using standard epoxy/glass (FR-4) processes at competitive prices.

RO4003C materials possess the necessary properties for designers of RF microwave circuits, matching networks, and controlled impedance transmission lines. Its low dielectric loss allows RO4003C to be used in applications where higher operating frequencies limit the use of conventional circuit board laminates. Available in various configurations, RO4003C laminates utilize both 1080 and 1674 glass fabric styles, all meeting the same laminate electrical performance specifications. RO4003C materials are non-brominated and do not have a UL 94 V-0 rating.

Dielectric Constant: DK 3.38 ± 0.05 at 10GHz Dissipation Factor: 0.0027 at 10GHz Thermal Conductivity: 0.71 W/m/°K Thermal Coefficient of Dielectric Constant: +40 ppm/°C, ranging from -50°C to 150°C CTE Matched to Copper: X-axis 11ppm/°C, Y-axis 14ppm/°C Low Z-Axis Coefficient of Thermal Expansion: 46 ppm/°C Tg: >280 °C Low Moisture Absorption: 0.06%

Low Z-Axis CTE: 2.4 ppm/°C, excellent through-hole reliability.High Tg: 185 °C, high heat resistance for lead-free FR-4. Low Water Absorption: 0.08%, humidity resistance. T260: 60 minutes, T288: 30 minutes. UL 94-V0 Flammability Rating.

Components: 41 Total Pads: 73 Thru Hole Pads: 35 Top SMT Pads: 26 Bottom SMT Pads: 12 Vias: 57 Nets: 6

Cellular Base Station Antennas and Power Amplifiers RF Identification Tags Automotive Radar and SensorsLNBs for Direct Broadcast Satellites Computing, Communication, Automotive Electronics

8-Layer HDI Hybrid PCB Stackup
8-Layer HDI Hybrid PCB

PCB specifications

Basic PCB SpecificationsParameters
Board Type8 layers
Material TypeRO4003C + FR-4 Tg170 °C
Solder MaskBoth sides, Green
Silkscreen PrintTop side, White
Surface FinishENIG
Total Board Thickness1.5mm ± 10%
Board Size87.5mm x 40.6mm (1 piece)
Minimum Hole Size0.2mm
Solder Mask Thickness10µm
Minimum Dielectric Thickness100µm
Minimum Trace Line Width115µm
Minimum Spacing135µm
Blind ViaYes, L1-L2, L7-L8
Buried ViaYes, L2-L7
Back Drilled ViaYes, L1-L6
Impedance Controlled- 50 ohm, differential pairs, Top layer, 4mil / 4mil trace/gap, reference layer 2

- 100 ohm, differential pairs, Top layer, 5mil / 6mil trace/gap, reference layer 2

- 50 ohm, single-ended, Top layer, 6mil trace, reference layer 2

All 0.3mm ViasFilled and capped according to IPC 4761 Type VII
Edge PlatingRequired

Layer stack-up

  1. COPPER · 1 · 45µm · 18µm BASE COPPER + 25µm PLATINGcopper
  2. RO4003C · CORE · 203µm · IPC-4101/24core
  3. COPPER · 2 · 38µmcopper
  4. FR-4 · PP · 100µm · IPC-4101/24core
  5. COPPER · 3 · 17µmcopper
  6. FR-4 S1000-2M · CORE · 240µm · IPC-4101/24core
  7. COPPER · 4 · 35µmcopper
  8. FR-4 · PP · 100µm · IPC-4101/24core
  9. COPPER · 5 · 35µmcopper
  10. FR-4 S1000-2M · CORE · 240µm · IPC-4101/24core
  11. COPPER · 6 · 17µmcopper
  12. FR-4 · PP · 100µm · IPC-4101/24core
  13. COPPER · 7 · 38µmcopper
  14. RO4003C · CORE · 200µm · IPC-4101/24core
  15. COPPER · 8 · 45µm · 18µm BASE COPPER + 25µm PLATINGcopper

Tell us the board. We answer within 4 hours.

Large Gerber files are easier by email — this form gets the conversation started with the right engineer.

Send request

Or email your files torfq@bichengcircuits.com