BICHENGPCBBicheng Technologies Limited

TMM10 2-Layer 0.5mm ENEPIG PCB – Microwave PCB for Antenna & Satellite

Custom product. Images and specifications are for reference only; the confirmed drawing governs.

Brief introduction

TMM 10 thermoset microwave materials offer the benefits of both PTFE and ceramic based substrates, but are not limited by the same mechanical properties and production techniques. This makes them an ideal choice for high-frequency and high-reliability applications where consistent dielectric performance and dimensional stability are critical. The TMM10 material system is specifically engineered to support demanding RF and microwave circuits, providing a robust alternative to conventional PTFE-based laminates without sacrificing electrical performance.

Dielectric Constant (Dk) of 9.20 +/- .230

Coefficient of thermal expansion matched to copper

Decomposition Temperature (Td) of 425 °C TGA

Coefficient of Thermal Expansion - x y z : 21ppm/K, 21ppm/K, 20ppm/K

Available in a thickness range of .0015 to .500 inches +/- .0015"

Mechanical properties resist creep and cold flow

Resistant to process chemicals, reducing damage during fabrication

Material does not require a sodium napthanate treatment prior to electroless plating

Based on a thermoset resin, allowing for reliable wire-bonding

Copper_layer_1 - 35 μmRogers TMM10 Core - 0.381 mm (15 mil)Copper_layer_2 - 35 μm

Components: 21Total Pads: 45Thru Hole Pads: 31Top SMT Pads: 14Bottom SMT Pads: 0Vias: 29Nets: 2

Chip testersDielectric polarizersSatellite communication systemsGPS antennas, and patch antennas etc.

Artwork supplied: Gerber RS-274-XAccepted standard: IPC-Class-2Availability: Worldwide

TMM® thermoset microwave materials are ceramic, hydrocarbon, thermoset polymer composites designed for high plated-thru-hole reliability stripline and microstrip applications. TMM laminates are available in a wide range of dielectric constants and claddings.

The electrical and mechanical properties of TMM laminates combine many of the benefits of both ceramic and traditional PTFE microwave circuit laminates, without requiring the specialized production techniques common to these materials. TMM laminates do not require a sodium napthanate treatment prior to electroless plating.

TMM laminates have an exceptionally low thermal coefficient of dielectric constant, typically less than 30 ppm/°C. The material's isotropic coefficients of thermal expansion, very closely matched to copper, allow for production of high reliability plated through holes, and low etch shrinkage values. Furthermore, the thermal conductivity of TMM laminates is approximately twice that of traditional PTFE/ceramic laminates, facilitating heat removal.

TMM laminates are based on thermoset resins, and do not soften when heated. As a result, wire bonding of component leads to circuit traces can be performed without concerns of pad lifting or substrate deformation.

TMM laminates combine many of the desirable features of ceramic substrates with the ease of soft substrate processing techniques. TMM laminates are available clad with 1/2 oz/ft² to 2 oz/ft² electrodeposited copper foil, or bonded directly to brass or aluminum plates. Substrate thicknesses of 0.015" to 0.500" are available. The base substrate is resistant to etchants and solvents used in printed circuit production. Consequently, all common PWB processes can be used to produce TMM thermoset microwave materials.

Ideal for single material systems on a wide variety of applications

High reliability of plated through holes

Reduces damage to material during fabrication and assembly processes

No specialized production techniques required

TMM10 and 10i laminates can replace alumina substrates

Application areas

  • Dielectric Constant (Dk) of 9.20 +/- .230
  • Dissipation factor of .0022 at 10GHz
  • Thermal coefficient of Dk of -38 ppm/°K
  • Coefficient of thermal expansion matched to copper
  • Decomposition Temperature (Td) of 425 °C TGA
  • Coefficient of Thermal Expansion - x y z : 21ppm/K, 21ppm/K, 20ppm/K
  • Thermal Conductivity of 0.76W/mk
  • Available in a thickness range of .0015 to .500 inches +/- .0015"
2-layer TMM10 PCB ENEPIG
CCL 123 TMM10

PCB specifications

Base materialTMM10
Layer countDouble sided
Board dimensions76mm x 118mm = 1PCS, +/- 0.15mm
Minimum Trace/Space4/6 mils
Minimum Hole Size0.35mm
Blind viasNo
Finished board thickness0.5mm
Finished Cu weight1oz (1.4 mils) outer layers
Via plating thickness20 μm
Surface finishENEPIG
Top SilkscreenWhite
Bottom SilkscreenNo
Top Solder MaskGreen
Bottom Solder MaskNo
100% Electrical testUsed prior to shipment

Tell us the board. We answer within 4 hours.

Large Gerber files are easier by email — this form gets the conversation started with the right engineer.

Send request

Or email your files torfq@bichengcircuits.com