BICHENGPCBBicheng Technologies Limited

TLY-5 7.5mil EPIG Ultra-Low Loss PTFE PCB for 77GHz Automotive Radar & Aerospace Applications

(Note: Printed Circuit Boards are custom-made products. Images and parameters are for reference only.)

Brief introduction

AGC TLY-5 laminates are manufactured with very lightweight woven fiberglass and are much more dimensionally stable than chopped fiber reinforced PTFE composites. The woven matrix in the TLY-5 material yields a more mechanically stable laminate that is suitable for high volume manufacturing. The low dissipation factor enables successful deployment for automotive radar applications designed at 77 GHz as well as other antennas in millimeter wave frequencies.

Comparative OEM testing at 77 GHz of lightly reinforced TLY-5 vs. its closest chopped fiber reinforced competitor has shown "drop in"/equivalent insertion losses/dielectric properties. The primary benefit is much higher manufacturing yields. The dielectric constant range is 2.17 to 2.40. For most thicknesses, the dielectric constant can be specified anywhere within this range with a tolerance of +/- 0.02. In the low dielectric constant range, the dissipation factor is approximately 0.0009 at 10 GHz.

This 2-layer rigid PCB is constructed with TLY-5 as the core material at 7.5mil (0.191mm) thickness, with EPIG (Electroless Palladium Immersion Gold) surface finish, no solder mask, no silkscreen, and 1oz copper on both sides. Its ultra-low DK of 2.20 and lowest Df of 0.0009 make it ideal for demanding millimeter-wave applications including automotive radar at 77 GHz, Ka/E/W band, and satellite communications.

TLY-5 laminates are manufactured with very lightweight woven fiberglass and are much more dimensionally stable than chopped fiber reinforced PTFE composites. The woven matrix in the TLY-5 material yields a more mechanically stable laminate that is suitable for high volume manufacturing. The low dissipation factor enables successful deployment for automotive radar applications designed at 77 GHz as well as other antennas in millimeter wave frequencies.

Comparative OEM testing at 77 GHz of lightly reinforced TLY-5 vs. its closest chopped fiber reinforced competitor has shown "drop in"/equivalent insertion losses/dielectric properties. The primary benefit is much higher manufacturing yields. The dielectric constant range is 2.17 to 2.40. For most thicknesses, the dielectric constant can be specified anywhere within this range with a tolerance of +/- 0.02. In the low dielectric constant range, the dissipation factor is approximately 0.0009 at 10 GHz. Typical applications include satellite communications, automotive radar, filters, couplers, avionics and phased array antennas.

TLY-3FF is a new highly flexible laminate designed for applications that require laminates with some bend radius. TLY-3FF is much more flexible than standard TLY-5 fiberglass reinforced substrates. The flexibility of TLY-3FF is comparable to chopped fiber reinforced PTFE laminates yet it has a loss tangent that is lower than traditional chopped fiber reinforced laminates. The fiberglass reinforced TLY-3FF has been engineered to provide the dimensional stability typical of the standard fiberglass reinforced TLY-5 Series yet offers the mechanical flexibility of chopped fiber reinforced laminates. TLY-3FF has also been designed for improved laser via formation relative to traditional TLY-5 glass reinforced laminates.

Technical features & benefits

  • Dielectric Constant (DK): 2.20 with tight tolerance ±0.02 at 10 GHz / 23°C
  • Lowest Dissipation Factor (Df): 0.0009 at 10GHz — Industry-leading low loss
  • Density (Specific Gravity): 2.19 g/cm³
  • Moisture Absorption: 0.02% — Extremely low
  • CTE X-axis: 26 ppm/°C, Y-axis: 15 ppm/°C, Z-axis: 217 ppm/°C
  • UL 94 V-0 Flammability Rating
  • NASA Outgassing: TML 0.01%, CVCM 0.01%, WVR 0.01% — Aerospace-grade
  • High Copper Peel Strength: 1.96~3.04 N/mm
  • Laser Ablatable — Suitable for laser via formation
  • EPIG Finish — Excellent solderability, corrosion resistance, and wire bondability
  • Dimensionally Stable — Woven fiberglass reinforcement provides superior mechanical stability for high volume manufacturing
  • Lowest Df (0.0009 @ 10GHz) — Ultra-low loss for millimeter-wave applications up to 77 GHz
  • Tight DK Tolerance (±0.02) — Uniform and consistent dielectric constant for reliable impedance control
  • Low Moisture Absorption (0.02%) — Excellent performance in humid environments
  • High Copper Peel Strength — Reliable copper adhesion for demanding applications
  • Lightweight Woven Fiberglass — More dimensionally stable than chopped fiber reinforced PTFE
  • Aerospace-Grade Reliability — NASA low outgassing, radiation resistance, high electrical strength
  • Laser Ablatable — Improved laser via formation for advanced PCB designs
  • DK 2.20 ± 0.02 @ 10GHz:Ultra-low and tightly controlled dielectric constant for consistent impedance
  • Df 0.0009 @ 10GHz:Industry-leading lowest dissipation factor for millimeter-wave applications
  • Lightweight Woven Fiberglass:Superior dimensional stability for high volume manufacturing
  • CTE: 26/15/217 ppm/K:Dimensional stability across temperature ranges
  • Moisture Absorption 0.02%:Excellent stability in humid environments
  • UL 94 V-0:Flame retardant for safety compliance
  • NASA Low Outgassing:Aerospace-grade reliability for space applications
  • EPIG Finish:Excellent solderability, corrosion resistance, wire bondability

Product images

TLY-5 PCB
TLY-5 Material

PCB specifications

Base materialAGC TLY-5 (Very Lightweight Woven Fiberglass PTFE)
Layer count2-layer
Board dimensions45mm x 87mm = 1 PCS, ±0.15mm
Minimum Trace/Space6/10 mils
Minimum Hole Size0.4mm
Blind viasNo
Finished board thickness0.3mm (including copper)
Finished Cu weight1 oz (35 μm / 1.4 mils) all layers
Via plating thickness20 μm
Surface finishEPIG (Electroless Palladium Immersion Gold)
Top SilkscreenNo
Bottom SilkscreenNo
Top Solder MaskNo
Bottom Solder MaskNo
100% Electrical testUsed prior to shipment
ParameterOptions
Standard Thickness0.0035" (0.09mm), 0.005" (0.13mm), 0.0075" (0.19mm), 0.010" (0.25mm), 0.020" (0.51mm), 0.030" (0.76mm), 0.060" (1.52mm)
Thickness IncrementsAvailable in 0.005" (0.125mm) increments
DK Range2.17 to 2.40 (specifiable with ±0.02 tolerance)
Standard Panel Sizes12"x18" (305x457mm), 16"x18" (406x457mm), 18"x24" (457x610mm), 16"x36" (406x914mm), 24"x36" (610x914mm), 18"x48" (457x1220mm)
Standard Copper Cladding½ oz ED, 1 oz CL1, 1 oz C1 copper
Special OptionsContact AGC for additional thicknesses, other sizes & any other type of cladding
Flexible OptionTLY-3FF — Highly flexible laminate with bend radius capability

Layer stack-up

  • Layer: Copper_layer_1 (Top), Material: Copper, Thickness: 35 μm (1 oz)
  • Layer: Dielectric, Material: TLY-5 Core, Thickness: 0.191 mm (7.5mil)
  • Layer: Copper_layer_2 (Bottom), Material: Copper, Thickness: 35 μm (1 oz)

PCB Statistics

  • Components: 37
  • Total Pads: 149
  • Thru Hole Pads: 85
  • Top SMT Pads: 64
  • Bottom SMT Pads: 0
  • Vias: 139
  • Nets: 2

Application areas

  • Automotive Radar (77 GHz and millimeter-wave frequencies)
  • Satellite and Cellular Communications
  • Power Amplifiers and High-Power RF Modules
  • LNBs, LNAs, LNCs (Low Noise Block Downconverters, Low Noise Amplifiers)
  • Aerospace and Avionics Systems
  • Ka, E and W Band Applications
  • Phased Array Antennas and Filters
  • Microwave Test Equipment and Couplers
  • Automotive Radar (77 GHz and millimeter-wave frequencies)
  • Satellite and Cellular Communications
  • Power Amplifiers and High-Power RF Modules
  • LNBs, LNAs, LNCs (Low Noise Block Downconverters, Low Noise Amplifiers)
  • Aerospace and Avionics Systems
  • Ka, E and W Band Applications
  • Phased Array Antennas and Filters
  • Microwave Test Equipment and Couplers

Properties

TLY-5 Typical Properties

PropertyTLY-5Dir.UnitsConditionTest Method
CompositionPTFE - Glass————
Dielectric Constant, Dk @ 10 GHz2.20Z—10 GHzIPC-TM-650 2.5.5.5
Dk Tolerance±0.02————
Dissipation Factor, Df @ 10 GHz0.0009Z—10 GHzIPC-TM-650 2.5.5.5
Moisture Absorption0.02—%—ASTM D570
Thermal Conductivity0.22ZW/(m·K)——
CTE (X)20Xppm/°C——
CTE (Y)20Yppm/°C——
CTE (Z)280Zppm/°C——
Peel Strength (1 oz Cu)12—lbs/in——
FlammabilityV-0———UL94

Quality Assurance

  • Type of artwork supplied: Gerber RS-274-X
  • Accepted standard: IPC-Class-2
  • Availability: Worldwide
  • 100% Electrical test prior to shipment
  • Type of artwork supplied: Gerber RS-274-X
  • Accepted standard: IPC-Class-2
  • Availability: Worldwide
  • 100% Electrical test prior to shipment

Tell us the board. We answer within 4 hours.

Large Gerber files are easier by email — this form gets the conversation started with the right engineer.

Send request

Or email your files torfq@bichengcircuits.com