BICHENGPCBBicheng Technologies Limited

Rogers DiClad 880 DK2.17/2.20 Df0.0009 (0.508-1.524mm) Copper Clad Laminate

Brief introduction

DiClad 880 is a woven fiberglass reinforced PTFE composite laminate designed for high-frequency printed circuit board applications. With dielectric constants of 2.17 and 2.20, it provides excellent electrical uniformity and low loss, making it ideal for RF and microwave circuits where signal integrity and dimensional stability are critical.

Technical features & benefits

  1. 1.Low Dielectric Constant: Dk = 2.17 or 2.20 at 10 GHz, with high uniformity across the panel.
  2. 2.Ultra-Low Loss: Dissipation factor as low as 0.0009 at 10 GHz.
  3. 3.Excellent Thermal Stability: Thermal coefficient of Dk = –160 ppm/°C for reliable performance over temperature.
  4. 4.High Electrical Insulation: Volume resistivity up to 1.4×10⁹ MΩ·cm, surface resistivity up to 2.9×10⁶ MΩ.
  5. 5.Good Mechanical Strength: Balanced tensile, compressive, and flexural modulus for reliable PCB fabrication.

Application areas

  • RF and Microwave Circuits: Filters, couplers, low-noise amplifiers (LNAs).
  • Power Dividers and Combiners: Where low loss and high uniformity are essential.
  • Aerospace and Defense: Radar systems, communication payloads.
  • Test and Measurement: Calibration boards and high-frequency fixtures.
  • Telecommunications: 5G infrastructure, satellite ground equipment.
Rogers DiClad 880 Laminate
DiClad 880 Chart 1
DiClad 880 Chart 2

Typical properties: Rogers DiClad 880

Material-level dielectric and mechanical properties, distinct from the board-level specifications above.

Open the standalone data sheet (printable)
Rogers DiClad 880
PropertyTypical ValueUnitsTest ConditionsTest Method
Dielectric Constant @10 GHz2.17, 2.20–23°C @ 50% RHIPC TM-650 2.5.5.5
Dielectric Constant @1 MHz2.17, 2.20–23°C @ 50% RHIPC TM-650 2.5.5.3
Dissipation Factor @10 GHz0.0009–23°C @ 50% RHIPC TM-650 2.5.5.5
Dissipation Factor @1 MHz0.0008–23°C @ 50% RHIPC TM-650 2.5.5.3
Thermal Coefficient of Dk–160ppm/°C–10°C to 140°C, 10 GHzIPC TM-650 2.5.5.5
Volume Resistivity1.4×10⁹MΩ·cmC96/35/90IPC TM-650 2.5.17.1
Surface Resistivity2.9×10⁶MΩC96/35/90IPC TM-650 2.5.17.1
Dielectric Breakdown>45kVD48/50ASTM D-149
Arc Resistance>180sec–ASTM D-495
CTE – X Direction25ppm/°C50°C to 150°CIPC TM-650 2.4.41
CTE – Y Direction34ppm/°C50°C to 150°CIPC TM-650 2.4.41
CTE – Z Direction252ppm/°C50°C to 150°CIPC TM-650 2.4.24
Thermal Conductivity0.25W/(m·K)–ASTM E1461
Copper Peel Strength14lbs/in10s @ 288°C, 35 μm foilIPC TM-650 2.4.8
Young's Modulus267, 202kpsi23°C @ 50% RHASTM D-638
Tensile Strength (MD, CMD)8.1, 7.5kpsi23°C @ 50% RHASTM D-882
Compressive Modulus237kpsi23°C @ 50% RHASTM D-695
Flexural Modulus357kpsi23°C @ 50% RHASTM D-3039
FlammabilityV-0–C48/23/50 & C168/70UL 94
Moisture Absorption0.02%E1/105 + D24/23IPC TM-650 2.6.2.2
Density2.23g/cm³C24/23/50, Method AASTM D792
Outgassing – Total Mass Loss0.01%125°C, ≤ 10⁻⁶ torrNASA SP-R-0022A
Outgassing – Collected Volatiles0.01%125°C, ≤ 10⁻⁶ torrNASA SP-R-0022A
Outgassing – Water Vapor Recovered0.00%125°C, ≤ 10⁻⁶ torrNASA SP-R-0022A

Available configurations

  • Standard Thicknesses: 0.020" (0.508 mm), 0.030" (0.762 mm), 0.060" (1.524 mm) with tight tolerances.
  • Panel Sizes: 12" × 18" (305 × 457 mm), 18" × 12" (457 × 305 mm), 18" × 24" (457 × 610 mm), 24" × 18" (610 × 457 mm).
  • Copper Claddings: Electrodeposited copper foil (½ oz and 1 oz) or reverse-treated electrodeposited copper foil.

Tell us the board. We answer within 4 hours.

Large Gerber files are easier by email — this form gets the conversation started with the right engineer.

Send request

Or email your files torfq@bichengcircuits.com