BICHENGPCBBicheng Technologies Limited

面向芯片测试机与卫星通信的 Rogers TMM13i 2 层 3.9mm OSP 电路板

定制产品,图片与规格仅供参考,具体以下单确认的图纸为准。

产品简介

The Rogers TMM13i isotropic thermoset microwave material is a ceramic thermoset polymer composite tailored for high reliability in plated thru-hole strip-line and micro-strip applications. It features an isotropic dielectric constant (Dk) and integrates the advantageous properties of both ceramic and PTFE substrates, while allowing for the convenience of soft substrate processing methods.

This 2-layer rigid PCB is constructed entirely with TMM13i as the core material, providing excellent signal integrity, thermal stability, and high-dielectric-constant performance for demanding RF and microwave applications.

Copper matched Coefficient of Thermal Expansion (-55 to 288°C): X axis 19 ppm/°C, Y axis 19 ppm/°C, Z direction 20 ppm/°C

Lead free Process Compatible, 94V-0 flammability

Mechanical properties resist creep and cold flow

Resistant to process chemicals, reducing damage during fabrication

Material does not require a sodium napthanate treatment prior to electroless plating

Based on a thermoset resin, allowing for reliable wire-bonding

Copper_layer_1 – 35 μm TMM13i – 3.81 mm (150 mil) Copper_layer_2 – 35 μm

Components: 29 Total Pads: 47 Thru Hole Pads: 19 Top SMT Pads: 28 Bottom SMT Pads: 0 Vias: 26 Nets: 2

Artwork supplied: Gerber RS-274-X Accepted standard: IPC-Class-2 Availability: Worldwide

9.TMM® Thermoset Microwave Materials – TMM13i High Frequency Materials

TMM® thermoset microwave materials are ceramic, hydrocarbon, thermoset polymer composites designed for high plated-thru-hole reliability stripline and microstrip applications. TMM laminates are available in a wide range of dielectric constants and claddings.

The electrical and mechanical properties of TMM laminates combine many of the benefits of both ceramic and traditional PTFE microwave circuit laminates, without requiring the specialized production techniques common to these materials. TMM laminates do not require a sodium napthanate treatment prior to electroless plating.

TMM laminates have an exceptionally low thermal coefficient of dielectric constant, typically less than 30 ppm/°C. The material's isotropic coefficients of thermal expansion, very closely matched to copper, allow for production of high reliability plated through holes, and low etch shrinkage values. Furthermore, the thermal conductivity of TMM laminates is approximately twice that of traditional PTFE/ceramic laminates, facilitating heat removal.

TMM laminates are based on thermoset resins, and do not soften when heated. As a result, wire bonding of component leads to circuit traces can be performed without concerns of pad lifting or substrate deformation.

TMM laminates combine many of the desirable features of ceramic substrates with the ease of soft substrate processing techniques. TMM laminates are available clad with 1/2 oz/ft² to 2 oz/ft² electrodeposited copper foil, or bonded directly to brass or aluminum plates. Substrate thicknesses of 0.015" to 0.500" are available. The base substrate is resistant to etchants and solvents used in printed circuit production. Consequently, all common PWB processes can be used to produce TMM thermoset microwave materials.

Coefficient of thermal expansion matched to copper

Ideal for single material systems on a wide variety of applications

High reliability of plated through holes

Reduces damage to material during fabrication and assembly processes

No specialized production techniques required

TMM10 and 10i laminates can replace alumina substrates

13.Standard Thicknesses, Panel Sizes & Claddings

Standard Claddings (Electrodeposited Copper Foil)

*Additional claddings such as heavy metal and unclad are available

应用领域

  • Dielectric Constant Dk of 12.85 ± 0.35
  • Dissipation factor of 0.0019 at 10GHz
  • Thermal coefficient of Dk of -70 ppm/°K
  • Lead free Process Compatible, 94V-0 flammability
150mil TMM13i PCB 2-layer ENIG
CCL 138 TMM13i

规格参数

Base materialTMM13i
Layer count2 layers
Board dimensions76.8mm x 97mm = 1PCS
Minimum Trace/Space4/5 mils
Minimum Hole Size0.25mm
Blind viasNo
Finished board thickness3.9mm
Finished Cu weight1 oz (1.4 mils) outer layers
Via plating thickness20 μm
表面处理OSP
Top SilkscreenNo
Bottom SilkscreenNo
Top Solder MaskNo
Bottom Solder MaskNo
100% Electrical testUsed prior to shipment

把板子告诉我,4 小时内回复

Gerber 文件太大可以直接发邮件,这个表单先把需求交给对应的工程师。

提交需求

或把资料发到rfq@bichengcircuits.com