BICHENGPCBBicheng Technologies Limited

面向微波与射频应用的 Rogers TMM3 2 层 100mil EPIG 高频电路板

定制产品,图片与规格仅供参考,具体以下单确认的图纸为准。

起订量
1PCS
交期
7-13 working days
包装
Vacuum / Anti-static Packaging
付款方式
T/T, Paypal

产品简介

1. Introduction to TMM3 High Frequency PCB

Rogers TMM 3 thermoset microwave material is a ceramic thermoset polymer composite designed for high plated thru-hole reliability strip-line and micro-strip applications.

TMM 3 laminates combine many of the benefits of both ceramic and traditional PTFE microwave circuit laminates without requiring the specialized production techniques common to those materials. TMM laminates are based on thermoset resins, making them reliable for wire-bonding without pad lifting or substrate deformation.

This 2-layer rigid PCB is constructed entirely with TMM3 as the core material at 100mil (2.54mm) thickness, with EPIG (nickel-free palladium gold) surface finish and 1oz copper on both sides. Its DK of 3.27 offers excellent high-frequency performance, making it ideal for demanding applications such as chip testers, dielectric polarizers, filters, GPS antennas, patch antennas, power amplifiers, and satellite communication systems.

Dielectric Constant (DK): 3.27 ± 0.032 at 10GHz

Dielectric Constant (Design): 3.45 (8 GHz - 40 GHz)

Dissipation Factor (Df): 0.0020 at 10GHz

Thermal Coefficient of DK (TCDK): 37 ppm/°K (-55°C to +125°C)

CTE matched to copper: X-axis 15 ppm/K, Y-axis 15 ppm/K, Z-axis 23 ppm/K (0°C to 140°C)

High Thermal Conductivity: 0.70 W/(M·K) — approximately twice that of traditional PTFE/ceramic laminates

EPIG (Electroless Palladium Immersion Gold) – Nickel-free finish

Finished board thickness: 2.54mm (100mil)

Stable DK (3.27±0.032) — Consistent impedance control for high-frequency designs

Low Df (0.0020 @ 10GHz) — Excellent high-frequency performance with minimal signal loss

CTE Matched to Copper (15/15/23 ppm/K) — High reliability plated through holes, dimensional stability

High Thermal Conductivity (0.70 W/m/K) — Approximately twice that of traditional PTFE/ceramic laminates

Thermoset Resin — No softening when heated, reliable wire-bonding without pad lifting or substrate deformation

Excellent Mechanical Properties — Resist creep and cold flow

Chemical Resistance — Resistant to etchants and solvents used in PCB production

No Sodium Napthanate Treatment Required — Simplified electroless plating process

EPIG Nickel-Free Finish — Excellent solderability, wire bondability, and corrosion resistance without nickel concerns

5. PCB Stackup (2-Layer Rigid Structure)

Rogers TMM3 Substrate – 2.54 mm (100mil)

7. Rogers TMM3 Material – Product Introduction

TMM laminates have an exceptionally low thermal coefficient of dielectric constant, typically less than 30 ppm/°C. The material's isotropic coefficients of thermal expansion, very closely matched to copper, allow for production of high reliability plated through holes, and low etch shrinkage values. Furthermore, the thermal conductivity of TMM laminates is approximately twice that of traditional PTFE/ceramic laminates, facilitating heat removal.

TMM laminates are based on thermoset resins, and do not soften when heated. As a result, wire bonding of component leads to circuit traces can be performed without concerns of pad lifting or substrate deformation.

TMM laminates combine many of the desirable features of ceramic substrates with the ease of soft substrate processing techniques. TMM laminates are available clad with 1/2 oz/ft² to 2 oz/ft² electrodeposited copper foil, or bonded directly to brass or aluminum plates. Substrate thicknesses of 0.015" to 0.500" are available. The base substrate is resistant to etchants and solvents used in printed circuit production. Consequently, all common PWB processes can be used to produce TMM thermoset microwave materials.

Global Positioning Systems (GPS) Antennas

Stripline and microstrip applications requiring high plated thru-hole reliability

Type of artwork supplied: Gerber RS-274-X

No sodium napthanate treatment required prior to electroless plating

12. Standard Thickness, Panel Sizes & Claddings

Prolonged exposure in an oxidative environment may cause changes to the dielectric properties of hydrocarbon based materials. The rate of change increases at higher temperatures and is highly dependent on the circuit design. Rogers recommends that the customer evaluate each material and design combination to determine fitness for use over the entire life of the end product.

The design Dk is an average number from several different tested lots of material and on the most common thickness/s. For more detailed information, please contact Rogers Corporation.

All test data are typical measurement values intended to assist customers in material selection. They do not constitute any express or implied warranty and do not guarantee performance in specific applications. Customers are responsible for verifying the suitability of Rogers materials for each application.

应用领域

  • Dielectric Constant (DK): 3.27 ± 0.032 at 10GHz
  • Dielectric Constant (Design): 3.45 (8 GHz - 40 GHz)
  • Dissipation Factor (Df): 0.0020 at 10GHz
  • Thermal Coefficient of DK (TCDK): 37 ppm/°K (-55°C to +125°C)
  • EPIG (Electroless Palladium Immersion Gold) – Nickel-free finish
  • No solder mask, no silkscreen
  • Board dimensions: 48.6mm x 50.04mm
  • Finished board thickness: 2.54mm (100mil)
  • Lead-Free Process Compatible
TMM3 2-Layer 100mil EPIG High Frequency PCB
TMM3 Material

规格参数

Base materialRogers TMM3 (Ceramic Thermoset Polymer Composite)
Layer count2-layer rigid PCB
Board dimensions48.6mm x 50.04mm = 1 PCS
Minimum Hole Size2.5mm
Blind viasNo
Finished board thickness2.54mm (100mil)
Finished Cu weight1 oz (35 μm / 1.4 mils) all layers
Via plating thickness20 μm
表面处理EPIG (Electroless Palladium Immersion Gold – Nickel-Free)
Top Solder MaskNo
Bottom Solder MaskNo
Top SilkscreenNo
Bottom SilkscreenNo
Quality standardIPC-Class-2
100% Electrical testUsed prior to shipment

把板子告诉我,4 小时内回复

Gerber 文件太大可以直接发邮件,这个表单先把需求交给对应的工程师。

提交需求

或把资料发到rfq@bichengcircuits.com